Video Input - NAD C300 Manuel D'installation

0 0
48 views
 
NAD C300
Uploaded by juvior
C300 Stereo Integrated Amplifier GB Owner's Manual F
D E I P S Manuel d'Installation Bedienungsanleitung
Manual del Usuario Manuale delle Istruzioni Manual do
Proprietário Bruksanvisning I...
   
Save Embed Share Print
NOTES ON INSTALLATION
Your NAD C300 should be placed on a firm, level surface. Avoid
placing the unit in direct sunlight or near sources of heat and damp.
Allow adequate ventilation. Do not place the unit on a soft surface
like a carpet. Do not place or it in an enclosed position such a
bookcase or cabinet that may impede the air-flow through the
ventilation slots. Make sure the unit is switched off before making
any connections.
The RCA sockets on your NAD C300 are colour coded for
convenience. Red and white are Right and Left audio respectively.
Use high quality leads and sockets for optimum performance and
reliability. Ensure that leads and sockets are not damaged in any
way and all sockets are firmly pushed home.
For best performance, use quality speaker leads of 16 gauge
(1.5mm) thickness or more.
If the unit is not going to be used for some time, disconnect the
plug from the AC socket.
Should water get into your NAD C300, shut off the power to the
unit and remove the plug from the AC socket. Have the unit
inspected by a qualified service technician before attempting to
use it again.
serviceable parts inside.
Use a dry soft cloth to clean the unit. If necessary, lightly dampen
the cloth with soapy water. Do not use solutions containing benzol
or other volatile agents.
QUICK START
1. Connect the speakers to the rear Speaker sockets and sources
to the relevant rear input sockets.
2. Plug in the AC power cord.
3. Press the POWER button to turn the NAD C300 on.
4. Press the required input selector.
REAR PANEL CONNECTIONS
GB
1. DISC INPUT
Input for additional line level input signals such as CD, Mini Disc
player or the output signal from a step-up amplifier for a
turntable. Use a twin RCA-to-RCA lead to connect the auxiliary
unit's left and right 'Audio Outputs' to this input.
2. CD INPUT
Input for a CD or other line-level signal source. Use a twin RCA-
to-RCA lead to connect the CD player's left and right 'Audio
Outputs' to this input. The NAD C300 only accepts analogue
signals from your CD player.

3. VIDEO INPUT

Full description
NAD C300 Stereo Integrated Amplifie
Do not remove the cover, there are no user-
RELATED TITLES
The Selection The Glass Castle:
A Memoir
5. TUNER INPUT
Input for a Tuner or other line-level signal source. U
to-RCA lead to connect the Tuner left and right 'Au
this input.
6. TAPE 2 IN, OUT
Connections for analogue recording and playbac
tape recorder of any type. Using twin RCA-to-RCA
to the left and right 'Audio Output' of the tape mach
2 IN sockets for playback and tape monitoring. C
and right 'Audio Input' of the tape machine to th
sockets for recording.
7. TAPE 1 IN, OUT
Connections for analogue recording and playback
audio tape recorder of any type. Using twin RCA
connect to the left and right 'Audio Output' of the ta
the TAPE 1 IN sockets for playback and tape monit
the left and right 'Audio Input' of the tape machine
OUT sockets for recording.
8. SPEAKERS
Speaker terminals for speakers with an impedance
more. Connect the right speaker to the terminals
and 'R-' ensuring that the 'R+' is connected to the
your loudspeaker and the 'R-' is connected to the lo
' terminal. Connect the terminals marked 'L+' and
speaker in the same way.
Always use heavy duty (16 gauge; 1.5mm, or thicker
to connect loudspeakers to your NAD C300. Th
binding post terminals can be used as a screw term
terminating in spade or pin sockets or for cables with
BARE WIRES AND PIN CONNECTORS
Bare wires and pin sockets should be inserted into
shaft of the terminal. Unscrew the speaker ter
bushing until the hole in the screw shaft is revealed
or bare cable end into the hole and secure the cabl
down the terminal's bushing.
Ensure bare wire from the speaker cables does not
panel or another socket. Ensure that there is only
bare cable or pin and no loose strands of speakers
9. AC LINE CORD
Plug the AC power cord into a live AC wall socket.
connections have been made before connecting to

Alexander Hamilton