Scheppach DP55 Traduction Des Instructions D'origine page 25

10.2 Setting the drilling depth (fig. 1, 11)
The drilling depth can be set with the depth stop (7).
1. Release the clamping lever on the depth stop (6).
2. Carry out a test drilling. As soon as the desired
depth, tighten the depth stop clamping lever (6)
again.
3. The depth stop (7) is now locked in the desired
drilling depth.
4. Then check the position of the angle display. If
necessary, loosen the pointer (18) with a Phillips
screwdriver, set the scale (20) to 0° position and
re-tighten the retaining screw (19).
10.3 Clamping/releasing drill bits (fig. 4, 7)
Caution! Always release the chuck key. Risk of
injury due to chuck key being thrown away!
10.3.1 Clamping
1. Fold the tension chuck guard (13) upwards.
2. Insert the chuck key (G).
3. Turn the chuck key (G) counterclockwise, to open
the clamping sleeve (E).
4. Insert the insertion tool (F).
5. Hold the insertion tool (F) firmly.
6. Turn the chuck key (G) clockwise, to close the
clamping sleeve (E) and to secure the insertion
tool.
7. Check that the insertion tool (F) is tightly fitted.
8. Pull the chuck key (G) apart.
10.3.2 Releasing:
1. Fold the tension chuck guard (13) upwards.
2. Insert the chuck key (G).
3. Turn the clamping sleeve (G) clockwise until the
installation tool (F) can be removed.
4. Pull the chuck key (G) apart.
10.4 Aligning workpieces
1. Switch on the laser cross via on/off switch (12.3).
2. The intersection of the two laser lines exactly indi-
cates the centre point of the drill.
3. Align your marking on the workpiece with the la-
ser cross.
10.5 Clamping the workpiece (fig. 6)
It must be possible to clamp the workpiece securely.
Do not work with workpieces that cannot be clamped
securely.
The cut-out of the quick clamp must be centrally
aligned with the hole to be drilled. Otherwise, the
drill bit or the chuck could be obstructed by the quick
clamp.
1. Position the workpiece with the help of the laser
cross.
2. Loosen the quick clamping lever (17).
3. Place the quick clamp (2) on the workpiece.
4. Turn the quick clamp lever (17) clockwise to clamp
the workpiece.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
5. Turn the quick clamp lever (17) counter-clockwise
to release the quick clamp (2)
10.6 Clamping larger workpieces (fig. 6)
Use the parallel stop (16) for larger workpieces:
1. Loosen the wing screws for the parallel stop (15)
and insert the parallel stop (16) into the grooves of
the base plate.
2. Tighten the wing screws for the parallel stop (15).
3. Align your workpiece against the parallel stop (16)
and clamp it with the quick clamp (2).
Warning! With workpieces that are wider or longer
than the tabletop, ensure that these are adequately
supported, e.g. through trestles or saw horses.
Workpieces that are longer or wider than the base
plate of the tabletop drill can tip if they are not proper-
ly supported. If the workpiece tips, this can damage
the chuck guard or the cutting tool.
10.7 Setting the drilling speed (fig. 4)
The correct speed must be set to suit the workpiece
to be drilled and the tool diameter.
10.7.1 Electronic speed control:
The speed of the individual gears can be seamlessly
adjusted with the electronic speed control:
Set the speed with the help of the speed control
(12.1/12.2).
The current speed can be seen on the display (9).
10.8 Switching on/off (fig. 1)
m Make sure that the chuck guard (13) is folded
down before switching on.
Switching on: Press the on switch (11) to switch the
device on.
Switching off: Press the off switch (10) to switch the
device off.
m Attention: The speed set during the drill-
ing process will be saved and will be kept until
changed or the electric tool is disconnected from
the mains. Once the electric tool is connected to
the power supply again it will start up with a pre-
set speed of 1500 rpm.
GB | 25