Virutex PD52X Mode D'emploi page 6

basic safety precautions should always be followed to
reduce risk of fire, electric shock and personal injury.
This hot air gun operates at 525°C (980ºF) with no visual
indication of temperature (no flame). Never leave the
device unattended, otherwise there is a high risk of fire.
The heat stream at the outlet nozzle will burn flesh.
Do not turn on the heat gun with the hand in front of
the nozzle. DO NOT USE NEAR COMBUSTIBLE LIQUIDS.
DO NOT USE FOR:
• Heating gas engines
• Heating car batteries
• Thawing refrigerator equipment.
WARNING.
Some dust created by power sanding, sawing, grinding,
drilling and other construction activities contains che-
micals known to cause cancer, birth defects or other re-
productive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on
how often you do this type of work.
To reduce your exposure to these chemicals: work in
a well ventilated area, and work with approved safety
equipment, such as those dust masks that are specially
designed to filter out microscopic particles.
WARNING.
This tool is capable of producing temperatures up to
500°C (930ºF) of flameless heat at the nozzle. ALWAYS:
• Direct the heat away from yourself and others.
• Prevent ignition of combustible materials on or near
the workpiece.
• Prevent blockage of intake and nozzle openings.
• Keep a fully charged fire extinguisher on hand.
• Allow the nozzle and accessory tips to cool to room
temperature before storage.
CAUTIONS
1. WARNING: Hidden areas such as behind walls, cei-
lings, floors, soffit boards and other panels may contain
flammable materials that could be ignited by the heat
gun when working in these locations. The ignition of
these materials may not be readily apparent and could
result in property damage and injury to persons. Do not
use if in doubt about this hazard. When working in these
locations, keep the heat gun moving in a back-and-forth
motion. Lingering or pausing in one spot could ignite
the panel or the material behind it.
2. This heat gun can produce up to 500°C (930ºF) of
flameless heat at the nozzle. Do not direct airstream
6
at clothing, hair or other body parts. Do not use as a
hair dryer.
3. Do not use near flammable liquids or in an explosive
environment (fumes, gases or dust).
Remove materials or debris, that may become ignited,
from work area.
4. Always hold tool by plastic enclosure. The metal nozzle
requires approximately 20 minutes to cool before it
can be touched. Do not touch the nozzle or accessory
tips until cool.
5. Do not store tool until nozzle has cooled to room
temperature. Place the tool in a clear area away from
combustible materials while cooling.
6. Do not cut off airflow by placing the nozzle too close
to the workpiece. Keep the air intake clean and clear
of obstructions.
7. Place the tool on a level surface with the support
rubber ring when tool is not hand held.
Place the cord in a position that won't cause tipping.
8. Do not leave the tool unattended while running or
cooling down. Otherwise there is a risk of fire.
9. Keep a fully charged fire extinguisher nearby.
10. Do not direct airflow directly on glass.
11. Shield the materials around the heated area to
prevent damage or fire.
12. Supply voltage must be the same as shown on the
specification plate.
13. Do not use in wet conditions.
14. Not to be used by children. This is not a toy and
should be respected.
15. Do not use in bath or over water.
16. Safety glasses should be worn when using this tool.
17. It is recommended that leather gloves be worn when
using a heat gun.
18. Always unplug after use.
19. WARNING: Extreme care should be taken when
stripping paint. The peelings, residue and vapors of paint
may contain lead, which is poisonous. Any pre-1977 paint
may contain lead and paint applied to homes prior to
1950 is likely to contain lead. Once deposited on surfaces,
hand to mouth contact can result in the ingestion of lead.
Exposure to even low levels of lead can cause irreversible
brain and nervous system damage; young and unborn
children are particularly vulnerable. Before beginning
any paint removal process you should determine whether
the paint you are removing contains lead. This can be
done by a professional who uses a paint analyzer to
check the lead contact of the paint to be removed.
LEAD-BASED PAINT SHOULD ONLY BE REMOVED BY
A PROFESSIONAL AND SHOULD NOT BE REMOVED
USING A HEAT GUN.
20. Don't allow the entrance of dust or waste in the
gun air intake. It can produce a fire or damage the tool.
21. The appliance is not to be used by children or persons
with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have