Initial Operation; Maintenance Work; Technical Data - Chamberlain HC500ML-24 Installation

INITIAL OPERATION

Check gate functionality manually when the drive has been
disengaged. Electrical operation is only possible with the control unit
that is supplied as standard.
Electrical connections: See control unit instructions.
Always ensure that the mechanical and electrical safety requirements
relevant to the given system are complied with. fig.7

MAINTENANCE WORK

The drive mechanics are maintenance-free. Check at regular
intervals (monthly) that the gate hardware and the drive are all firmly
in place. Disengage the drive and check gate functionality. Only an
easy-running gate will work well with a drive. A drive is no substitute
for a poorly functioning gate.
A sliding gate can also be secured by implementing on-site
measures (fence, wall, etc.). See fig.8.
WARRANTY
Chamberlain GmbH warrants to the first retail purchaser of thisproduct that the product shall be free from any defect in materials and/or
workmanship for a period of 24 full months (2 years) from the date of purchase. Upon receipt of the product, the first retail purchaser is under
obligation to check the product for any visible defects.
Conditions: The warranty is strictly limited to the reparation or replacement of the parts of this product which are found to be defective and does not
cover the costs or risks of transportation of the defective parts or product. This warranty does not cover non-defect damage caused by unreasonable
use (including use not in complete accordance with Chamberlain's instructions for installation, operation and care; failure to provide necessary
maintenance and adjustment; or any adaptations of or alterations to the products), labor charges for dismantling or reinstalling of a repaired or
replaced unit or replacement batteries. A product under warranty which is determined to be defective in materials and/or workmanship will be
repaired or replaced (at Chamberlain's option) at no cost to the owner for the repair and/or replacement parts and/or product. Defective parts will be
repaired or replaced with new or factory rebuilt parts at Chamberlain's option. If, during the warranty period, the product appears as though
it may be defective, contact your original place of purchase.
This warranty does not affect the purchaser's statutory rights under applicable national legislation in force nor the purchaser's rights against
the retailer arising from their sales/purchase contract. In the absence of applicable national or EU legislation, this warranty will be the purchaser's
sole and exclusive remedy, and neither Chamberlain nor its affiliates or distributors shall be liable for any incidental or consequential damages for
any express or implied warranty relating to this product. No representative or person is authorized to assume for Chamberlain any other liability in
connection with the sale of this product.
D e c l a r a t i o n o f C o n f o r m i t y
Automatic Gate Opener Models HC500ML-24, TPD500-24 Series are in conformity to the
applicable sections of Standards
EN300220-3 • EN55014 • EN61000-3 • EN60555, EN60335-1 • ETS 300 683 • EN60335-
1: 2002 • EN60335-2-103: 2003 • EN55014-1: 2000 + A1 + A2 • EN55014-2: 2001 •
EN61000-3-2: 2000 • EN61000-3-3: 1995 + A1 • EN 301 489-3, V1.3.1 • EN 300 220-3
V1.1.1 • EN13241-1
per the provisions & all amendments
of the EU Directives .............................................2006/95/EC, 2004/108/EC, 1999/5/EG
D e c l a r a t i o n o f I n c o r p o r a t i o n
Automatic Gate Opener Models when installed and maintained according to all the
Manufacturer's instructions in combination with a Gate, which has also been installed and
maintained according to all the Manufacturer's instructions, meets the provisions of EU
Directive 2006/42/EEC and all amendments.
I, the undersigned, hereby declare that the equipment
specified above and any accessory listed in the manual
Christoph Marny
Manager, Regulatory Affairs
Chamberlain GmbH
D-66793 Saarwellingen
December, 2011

TECHNICAL DATA

Voltage IN
Frequency
Motor
Power
Current rated
Torque
Travel Speed
Duty Cycle
Working Temperatur
Range
Protection Class
Degree of Protection
Weight
approx. Gate Length
Max. Gate weight at
max. length (incl.
20% reserve)
conforms to the above Directives and Standard
230 Volt
50 Hz
24 V
60 W
2.5 A
10 Nm
12 cm/sec
30/24h
-20 O C - 55 O C
IP 44
I
8
8 m
500 kg
s.