Operation Procedures; Adjusting Mic Input Channels (1-6); Adjusting Line Input Channels (1-6); Adjusting The Input Of A Mic Connected To The Main Mic Input Jack - Tascam MZ-372 Mode D'emploi

Operation procedures

After turning the power on, adjust the levels of the
input signals.

Adjusting mic input channels (1-6)

1.
Set the channel 1–6 GAIN (
to their center values.
2.
Press the channel 1–6 SOURCE SELECT (
MIC switches so the C/MIC indicators (
3.
When connecting a mic to a channel 1–6 C
(MONO) /MIC ( ) input jack, set the INPUT
h
LEVEL switch ( ) to MIC.
j
4.
Set the MAIN OUTPUT VOL (
5.
Try speaking into the mic.
Use the channel 1–6 GAIN (
the input level so that its level meter (
around 0 dB.
6.
Use the channel 1–6 EQ (
equalizer.
7.
Follow the above procedures for other input
channels with connected mics.

Adjusting line input channels (1-6)

1.
Set the channel 1–6 GAIN (
to their center values.
2.
When connecting an audio device to channel
1–6, press the SOURCE SELECT switch (
that the SOURCE SELECT indicator (A/B/C/MIC)
lights.
3.
When connecting an audio device to a channel
1–6 C (MONO) /MIC (
INPUT LEVEL switch (
When connecting an audio device to channel 1–6
LINE A/B (v) input jacks, set the LINE/PHONE
) to LINE.
switch (
k
4.
Set the MAIN OUTPUT VOL (
5.
Start playback on the connected audio device.
Use the channel 1–6 GAIN (
the input level so that its level meter (
around 0 dB.
6.
Use the channel 1–6 EQ (
equalizer.
7.
Follow the above procedures to adjust other
input channels with connected audio devices.
14
TASCAM MZ-372
) and EQ (
) knobs
4 r
) C/
5
) light.
2
) knob levels low.
8
) knob to adjust
4
) lights
t
) knobs to adjust the
r
) and EQ (
) knobs
4 r
), so
5
) input jack, set the
h
) to LINE.
j
) knob levels low.
8
) knob to adjust
4
) lights
t
) knobs to adjust the
r
Adjusting the input of a mic connected
to the MAIN MIC INPUT jack
1.
Connect a mic to the MAIN MIC INPUT jack (
and press the MAIN MIC (
MIC (
) indicator lights.
2
2.
Use the MAIN MIC INPUT VOLUME (
adjust the mic input level.
3.
Use the MAIN MIC INPUT EQ (
the 2-band (HIGH/LOW) equalizer for the mic
sound.

Output channels

Output signals can be sent to the following jacks from
the stereo output bus.
0 MAIN OUTPUTS 1-2 (UNBALANCED) (
MAIN OUTPUTS 1-2 (BALANCED) (
0 SUB OUTPUT (
) jacks
x
0 MONITOR OUT (
z
NOTE
The output level from the MONITOR OUT (
jacks cannot be adjusted.
Adjusting the levels output from the MAIN
OUTPUTS 1-2 (UNBALANCED) and MAIN
OUTPUTS 1-2 (BALANCED) jacks
While checking the output level indicators (
) and MAIN OUTPUT VOL (
the channel faders (
6
knobs to adjust the output levels. The optimal output
level adjustment is usually when the output level
indicators ( ) light around 0 dB.
7
When an amplifier is connected to the MAIN OUT-
PUTS 1-2 (UNBALANCED) (
1-2 (BALANCED) ( ) jacks, set the ATTENUATOR (
c
switch to OFF if it accepts high gain or ON (-6dB) if it
accepts low gain.
Adjusting the level output from the SUB
OUTPUT jacks
Use the SUB OUTPUT VOL (
output level.
If the MONO (
) switch is set to ON (MONO indicator
0
lit) mono signals will be output from all output jacks.
To output mono signals from only the SUB OUTPUT
) jacks, set the SUB OUTPUT (d) switch to MONO.
(
x
) switch so the MAIN
2
) knob to
1
) knobs to adjust
e
f
) jacks
c
) jacks
7
) or MAIN OUTPUTS
f
) knob to adjust the
q
),
w
) and
)
z
), use
)
8
)
g