Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Hardware
A1
(2) 3/8"
Washers
A2
(2) 1/2" OD
Aluminum Sleeves
A3
(2) 3/8" x 3 1/4"
Hex Head Bolts
A4
(2) 3/8"
Nyloc Nuts
B1
(2) 3/8" x 2
Hex Head Bolts
B2
(2) 3/8"
Washers
B3
(2) 3/8"
Nyloc Nuts
C1
(2) 1/4" x 2 1/2"
Panhead Bolts
(2) 1/4"
Nyloc Nuts
C2
D1
(2) 1/4" x 1 3/4"
Panhead Bolts
D2
(2) 1/4"
Nyloc Nuts
(2) 1/4"
Washers
D3
NOTE: All parts are
shown at actual size.
Use the graphics
to match up the
corresponding part, or
use the ruler provided.
Phillips Head Screw Driver
Vaseline
5
USE FOR WHEELS: STEPS 3-5
USE FOR LEGS TO BASE: STEPS 6-7
USE FOR FEET TO LEGS: STEPS 8-10
USE FOR UPPER LEGS
TO LOWER LEGS: STEPS 12-13
Adjustible Wrench
3/8" & 1/4" Wrench
Ratchet Wrench
Assembly Instructions
Step 1
Step 2
Place base frame upside down as
Insert lower legs into base (parts
shown on a table or workbench.
are labeled Left and Right). Align
with bolt holes and push leg down
to snap in.
Step 5
Step 6
Using two wrenches, tighten to a
Insert hex bolt B1 into hole A. Head
snug fit. Allowing the wheels to
of bolt to be outside of base. Add
turn freely.
washer B2 to bolt from inside of base.
Attach nyloc nut B3 and tighten.
Step 9
Step 10
Hold foot firmly against leg. Place nyloc bolt
Repeat procedure for opposite
C2 into foot (flat side down). Apply pressure
foot.
to the nut (use back of pencil or screw-
driver) while turning the bolt to allow
threads on the nut to catch and tighten.
Step 13
Step 14
Insert pan-head bolts D1 with nyloc
Add Vaseline to leg tops first. Using two
bolt D2 and washer D3 on inside of
hands, lower the power head onto leg
leg. Tighten until moderately tight
assembly aligning holes in power head
with wrench and screwdriver.
to leg tops. Fully tighten legs assembly.
Step 3
Step 4
Attach wheel with flat surface facing
Attach nyloc nut A4 to wheel
out. Insert washer A1 and aluminum
assembly.
sleeve A2 onto longest hex head bolt
A3 and place through hole on flat
side of wheel and insert into hole B.
Step 7
Step 8
Repeat steps 2-6 for opposite
Place base frame on its side. Insert
lower leg. Note that lower legs
2-1/2" pan head C1 bolt through
turn in, towards center.
hole in leg and foot. Align foot with
straighter edge toward curved leg.
Step 11
Step 12
Turn completed base/leg/wheel
Attach upper legs by sliding onto
assembly to upright position. Add
lower legs. Align bolt holes in
Vaseline to tops of legs.
upper and lower legs. Repeat
procedure for opposite leg.
Step 15
Step 16
Open net door by turning latch
Take net and hold with string of
clockwise. Carefully open net door.
net facing door. Make sure net
entrance is fully open and that
drawstring is not pulled.
6
Publicité
Table des Matières
