baltur SPARK 18 W Manuel D'instructions page 21

• If the burner repeatedly shuts down in lock-out, do not
keep trying to manually reset it but call a qualified techni-
cian to solve the unexpected problem.
• If you decide not to use the burner for a while, close the
valve or valves that supply the fuel.
Special instructions for using gas.
• Check that the feed line and the train comply with current
standards and regulations.
• Check that all the gas connections are properly sealed.
• Do not leave the equipment on when it is not in use and
always close the gas cock.
• If the user is away for some time, close the main gas feed
valve to the burner.
• If you smell gas:
- do not operate electrical switches, the phone or any
other object that can cause sparks;
- immediately open doors and windows to create a
draught to clear the air in the room;
- close the gas cocks;
- have professionally qualified personnel correct the
fault.
• Do not block ventilation openings in the room where there
is gas equipment or dangerous situations may arise with
the build up of toxic and explosive mixtures.
FUEL SAFETY INSTRUCTIONS
• If the user is away for some time, close the main gas feed
valve to the burner.
• If you smell gas:
- do not operate electrical switches, the phone or any
other object that can cause sparks;
- immediately open doors and windows to create a
draught to clear the air in the room;
• close the gas cocks
• have professionally qualified personnel correct the fault.
INSTRUCTIONS ON ELECTRICAL SAFETY
• Check that the equipment is properly grounded according
to the safety standards in force.
• Do not use the gas pipes to ground electrical equipment.
• If in doubt, call for a careful electrical check by a qualified
technician, since the manufacturer will not be liable for any
damage caused by a poor ground connection.
• A professional check should be carried out to ensure that
the electrical installation is adequate for the maximum ou-
tput absorbed by the system. This is indicated on the data
plate.
• Make sure that the system cable cross-section is suitable
for the power absorbed by the equipment.
• The use of adaptors, multiple plugs and/or extension leads
to supply power from the mains to the appliance is not al-
lowed.
• For the connection to the mains, fit an omnipolar switch
with a contact opening gap equal to or greater than 3 mm
in accordance with current safety regulations (Overvoltage
category III).
• Use only double insulated cables with external thickness
of at least 1mm for the power supply of the burner.
• Unsheathe the external insulating cover of the power cable
to the necessary extent for the connection, thus avoiding
the wire from coming into contact with metal parts.
• The electrical supply to the burner must have neutral to
ground connection. In the case of a ionisation current
check with neutral not to ground, it is essential to make a
connection between terminal 2 (neutral) and the ground for
the RC circuit.
• If the user is away for some time, close the main gas feed
valve to the burner.
• The use of any components that use electricity means that
certain fundamental rules have to followed, including the
following:
- do not touch the equipment with parts of the body that
are wet or damp and/or with damp feet
- do not pull on electrical cables;
- do not leave the equipment exposed to atmospheric
agents (such as rain or sun etc.) unless there is express
provision for this.
- do not allow the equipment to be used by children or
inexperienced persons.
- The power supply cable for the equipment not must be
replaced by the user. If the cable is damaged, turn off
the equipment. To replace the cable, contact exclusively
qualified personnel.
- If you decide not to use the equipment for a while it is advi-
sable to switch off the electrical power supply to all compo-
nents in the system that use electricity (pumps, burner, etc.).
• Use flexible cables compliant with standard EN60335-1:
- if PVC sheathed at least H05VV-F
- if rubber sheathed at least H05RR-F
- if unsheathed at least FG7 or FROR
21 / 56
0006080405_201612