Introduction To Working With The Mortar Spraying Machine Powrplast; Function Of The Mortar Spraying Machine Powrplast 600; Processible Coating Materials; Technical Data - Titan PowrPlast 600 Mode D'emploi

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

PowrPlast 600
2
INtRODuctION tO WORkING WItH
tHe MORtAR SPRAyING MAcHINe
POWRPLASt 600
The suction pump PowrPlast 600 is conceived for using and
processing ready mixed mineral coating materials from a
bucket.
The material supply is ensured by the immersion of the suc-
tion tube into the material bucket.
The machine is not designed for use as a cleaning device.
2.1
FuNctION OF tHe MORtAR SPRAyING MAcHINe
POWRPLASt 600
The coating material is fed through the suction effect of the
screw pump. The suction effect causes the coating material
to enter the eccentric screw pump. This pump builds up the
pressure required for transportation through the mortar hose.
The compressed air required for atomisation is supplied at the
spray lance. The mortar spraying machine can be switched on
and off using the electric control. This can also be used to con-
trol the delivery volume.
A soft even spray pattern can be achieved by means of the
smoothly regulated convey capacity of the coating material.
2.2

PROceSSIBLe cOAtING MAteRIALS

• Thermal insulation composite system bonding agent
(mineral and artificial resin systems)
• Artificial resin plasters up to 3 mm granular size
• Silicate plasters up to 3 mm granular size
• Silicone resin plasters up to 3 mm granular size
• Mineral final coats up to 3 mm granular size
• Lightweight plaster systems up to 3 mm granular size
• Scraped stucco up to 3 mm granular size
• Thermal insulation plasters
• Restoration plaster
• Porous concrete coating
• Quartz plastic
• Roof coatings
• Fire protection coatings
• Mineral sealing sludges
• Bitumen emulsions
• Armoring filler
• Liquid wood-chip wall paper
• Casement grouting mortar
• Artificial resin rendering base
• Wash primer
• Filling paint, also fibrous
• Elastic coating
• Acoustic plaster, artificial resin bonded
• Fillers, artificial resin bonded
All the coating materials must be suitable for machine process-
ing. Refer to the product data sheet of the coating material to
be processed.
Use other coating materials only after agreement with the
manufacturer or the Titan application technology service.
3

tecHNIcAL DAtA

Voltage:
Fusing:
Device supply cable:
Motor output P
:
1
Max. convey capacity (water):
Max. operating pressure:
Max. granular size:
Dimensions L x W x H:
Weight (PowrPlast 600):
Weight (Spray lance):
Max. tyre pressure:
Degree of protection:
Max. sound pressure level:
Atomizing air connection:
Max. atomizing air pressure:
Minimum required compressed
air volume:
Max. mortar hose length:
Max. delivery height:
* Place of measurement: 1 m distance from unit and 1.60 m
above reverberant floor.
GB
IntroDuctIon
PowrPlast 600
230 V~, 50 Hz
16 A time-lag
5 m long, 3 x 1.5 mm
2
1.8 kW
12 l/min
40 bar
K3 mm
700 x 600 x 1050 mm
38 kg
2.1 kg
2.5 bar
IP 55
70 dB (A)*
Rapid action coupling
DN 7.2 mm
10 bar
280 l/min
30 m (and 2.5 m hose
whip)
20 m
33

Publicité

Table des Matières
loading

Table des Matières