Spypoint FL-8 Manuel D'utilisation page 4

6
POWER
The battery level is shown
screen. When a single line remains, the camera will continue to take
pictures but we strongly recommend changing the batteries before
they are empty. (See figure below)
AA BATTERIES
This camera requires the use of 6 AA batteries (1.5V). The use of
alkaline or lithium batteries is strongly recommended. During the
installation of AA batteries, place the switch inside the battery case
to «ALK» (i.e. alkaline). Insert the batteries as indicated inside the
battery case. Exact polarity must be followed. We also recommend
the use of new batteries to ensure maximum performance of your
camera.
LITHIUM BATTERY PACK
The camera can be powered by a rechargeable lithium battery LIT-
09/LIT-C-8 (sold separately, see section «OPTIONS»). This type of
battery is less affected by cold temperatures and lasts up to 3 times
longer than an alkaline battery. During the installation of lithium
battery, place the switch inside the battery case to «RECH»
EXTERNAL (12V)
The camera can be powered from an external 12-volt DC input
such as a 12-volt battery (KIT-12V/BATT-12V, sold separately) or
a 12-volt adapter (AD-12V, sold separately). When using a 12-volt
connection, we recommend removing the AA batteries to prevent
surcharges. During the installation of a 12-volt connection, place the
switch inside the battery case to «ALK» (i.e. alkaline). If combined
with a lithium battery pack, slide the switch to «RECH». To find
the accessories available for the 12-volts, see section «OPTIONS».
SOLAR PANEL
This model also offers the possibility of a connection to a solar panel
SP-12V (sold separately, see section «OPTIONS») to maintain the
charge of the lithium battery pack LIT-09/LIT-C-8 (sold separately,
see section «Options»). During the installation of the rechargeable
lithium battery, slide up the switch inside the battery case up to
« RECH » to activate the charging system of the solar panel.
in the lower left corner of the
LCD
.
MEMORY STORAGE
Using a memory card (sold separately, see section «OPTIONS») is
required to operate the camera. When the camera is «ON» and no
memory card is used, the LCD panel displays «CArd» meaning to
The camera is compatible with SD/SDHC memory
insert one.
card, up to 32 GB capacity. Before inserting or removing a
memory card, the camera must be turned off. Failing to do
so may cause loss of pictures or damage the pictures already
saved on the memory card.
When the SD card is full, the LCD
panel indicates «FULL». The following data shows an approximate
quantity of photos which can be recorded by the camera depending
on the memory card capacity.
RESOLUTION 2.0 GB
3 MP 2000
8 MP 1200
VIDEO RESOLUTION
320 x 240 2h
640 x 480 65 min
« BUSY » LED
The « BUSY » light, located next to the screen, lights up when the
.
camera is recording
SETTINGS
Date, Time, Temperature and Picture Quality
Turn «OFF» your camera;
«SET/TEST » and turn «ON» the camera and press «MENU/
OK». An «H» will flash on the screen indicating that the
camera is in High Resolution (8 MP). Use the «DOWN» button
if you want to reduce the resolution to «L» (3 MP). Press
«MENU/OK» to set the date and time (mm/dd/yy, hh/mm). Use
«UP» and «DOWN» to change the blinking digit. Choose «F» or
«C» to display the temperature in Fahrenheit (°F) or Celsius (°C).
Press «MENU/OK» to move to the next option. With the «UP»
button, choose «ON» or «OFF» to enable or disable the MS-1. This
option allows to trigger the camera remotely using one or more
MS-1 devices. (see section «Options» for more details)
4.0 GB 8.0 GB 32 GB
4100 8200 32800
2400 4800 19000
4h 8h 32h
2h10 4h10 16h40
set switch «MODE» to
7