Gas Installation; B-Vent - Model Cs500 - Continental Fireplaces CDVS500N Instructions D'installation Et D'opération

28
4.4

GAS INSTALLATION

EN
RISK OF FIRE, EXPLOSION OR ASPHYXIATION. ENSURE THERE ARE NO IGNITION SOURCES SUCH AS
SUPPORT GAS CONTROL WHEN ATTACHING GAS SUPPLY PIPE TO PREVENT DAMAGING GAS LINE.
28
ALWAYS LIGHT THE PILOT WHETHER FOR THE FIRST TIME OR IF THE GAS SUPPLY HAS RUN OUT
WITH THE GLASS DOOR OPENED OR REMOVED. PURGING OF THE GAS SUPPLY LINE SHOULD BE
4.4 GAS INSTALLATION
PERFORMED BY A QUALIFIED SERVICE TECHNICIAN. ASSURE THAT A CONTINUOUS GAS FLOW IS AT
THE BURNER BEFORE CLOSING THE DOOR. ENSURE ADEQUATE VENTILATION. FOR GAS AND
EN
ALL GAS CONNECTIONS MUST BE CONTAINED WITHIN THE APPLIANCE WHEN COMPLETE.
RISK OF FIRE, EXPLOSION OR ASPHYXIATION. ENSURE THERE ARE NO IGNITION SOURCES SUCH AS
HIGH PRESSURE WILL DAMAGE VALVE. DISCONNECT GAS SUPPLY PIPING BEFORE TESTING GAS
SUPPORT GAS CONTROL WHEN ATTACHING GAS SUPPLY PIPE TO PREVENT DAMAGING GAS LINE.
ALWAYS LIGHT THE PILOT WHETHER FOR THE FIRST TIME OR IF THE GAS SUPPLY HAS RUN OUT
Installation and servicing to be done by a qualifi ed installer.
WITH THE GLASS DOOR OPENED OR REMOVED. PURGING OF THE GAS SUPPLY LINE SHOULD BE
PERFORMED BY A QUALIFIED SERVICE TECHNICIAN. ASSURE THAT A CONTINUOUS GAS FLOW IS AT
THE BURNER BEFORE CLOSING THE DOOR. ENSURE ADEQUATE VENTILATION. FOR GAS AND
A.
Move the appliance into position and secure.
B.
If equipped with a fl ex connector the appliance is designed to accept a 1/2" (13mm) gas supply.
ALL GAS CONNECTIONS MUST BE CONTAINED WITHIN THE APPLIANCE WHEN COMPLETE.
Without the connector it is designed to accept a 3/8" (9.5mm) gas supply. The appliance is equipped
HIGH PRESSURE WILL DAMAGE VALVE. DISCONNECT GAS SUPPLY PIPING BEFORE TESTING GAS
with a manual shut off valve to turn off the gas supply to the appliance.
C.
Connect the gas supply in accordance to local codes. In the absence of local codes, install to the
Installation and servicing to be done by a quali ed installer. Do not use open fl ame.
current CAN/CSA-B149.1 Installation Code in Canada or to the current National Fuel Gas Code, ANSI
Z223.1 / NFPA 54 in the United States.
• Move the appliance into position and secure.
• If equipped with a ex connector the appliance is designed to accept a 1/2" (13mm) gas supply.
D.
When flexing any gas line, support the gas valve so that the lines are not bent or kinked.
Without the connector it is designed to accept a 3/8" (9.5mm) gas supply. The appliance is equipped
with a manual shut off valve to turn off the gas supply to the appliance.
E.
The gas line fl ex-connector should be installed to provide suffi cient movement for shifting the burner
• Connect the gas supply in accordance to local codes. In the absence of local codes, install to the
assembly on its side to aid with servicing components.
current CAN/CSA-B149.1 Installation Code in Canada or to the current National Fuel Gas Code, ANSI
Z223.1 / NFPA 54 in the United States.
F. Check for gas leaks by brushing on a soap and water solution. Do not use open fl ame.
• When exing any gas line, support the gas valve so that the lines are not bent or kinked.
• Check for gas leaks by brushing on a soap and water solution.

4.4.1 B-VENT - MODEL CS500

4.4.1 B-VENT - MODEL CS500
Attach one lead from the spill switch (white wire) to terminal #3 (TP/TH) located on the gas valve and the other
Attach one lead from the spill switch (white wire) to terminal #3 (TP/TH) located on the gas valve and the other
(black) on/off switch lead to valve terminal #1 (TH).
(black) on/off switch lead to valve terminal #1 (TH).
3
3
2
2
1
1
Attach the B-Vent label, as illustrated, in the control area of the appliance.
Attach the B-Vent label, as illustrated, in the control area of the appliance.
W415-1430 / B / 07.31.18
SPARKS OR OPEN FLAMES.
ELECTRICAL LOCATIONS, SEE "DIMENSIONS" SECTION.
!
SPARKS OR OPEN FLAMES.
LINE AT TEST PRESSURES ABOVE 1/2 PSIG.
VALVE SETTINGS HAVE BEEN FACTORY SET, DO NOT CHANGE.
ELECTRICAL LOCATIONS, SEE "DIMENSION" SECTION.
LINE AT TEST PRESSURES ABOVE 1/2 PSIG.
VALVE SETTINGS HAVE BEEN FACTORY SET, DO NOT CHANGE.
WARNING
!
WARNING
ATTACH THIS LABEL IN THE CONTROL AREA OF THE APPLIANCE.
THIS APPLIANCE HAS BEEN CONVERTED TO A NATURAL VENT
ATTACHEZ CET ETIQUETTE DANS LA REGION DE CONTROLE DUE FOYER.
CET APPAREIL A ÉTÉ CONVERTI À UN MODÈLE À TIRAGE
30.1A
MODEL.
NATUREL.
A / W385-0160