Important Safety Instructions; Grounding Instructions; Operating Safety Rules And Practices; Maintenance And Re- Build Practices - Windsor Pivot Instructions

IMPORTANT SAFETY IN-
STRUCTIONS
READ ALL INSTRUCTIONS
BEFORE USING.
WARNING
To reduce the risk of fire, electric
shock, or injury:
Do not leave machine when
–
plugged in. Unplug from outlet when
not in use and before servicing.
WARNING
TO REDUCE THE RISK OF ELEC-
–
TRIC SHOCK-USE INDOORS
ONLY
Do not allow to be used as a toy.
–
Close attention is necessary when
used by or near children.
Use only as discribed in this manu-
–
al. Use only manufacturer`s recom-
mended attachments.
Do not use with damaged cord or
–
plug. If machine is not working as it
should, has been dropped, dam-
aged, left outdoors, or dropprd into
water, return it to a service center.
Do not pull or carry by cord, use
–
cord as a handle, close a door on
cord, or pull cord around sharp edg-
es or corners. Do not run machine
over cord. Keep cord away from
heated surfaces.
Do not unplug by pulling on cord. To
–
unplug, grasp the plug, not the cord.
Do not handle plug or machine with
–
wet hands.
Do not put any object into openings.
–
Do not use with any opening
blocked; keep free of dust, lint, hair,
and anything that may reduce air
flow.
Keep hair, loose clothing, fingers,
–
and all parts of body away from
openings and moving parts.
Turn off all controls before unplug-
–
ging.
Use extra care when cleaning on
–
stairs.
Do not use to pick up flammable or
–
combustible liquids, such as gaso-
line, or use in areas where they may
be present.
Connect to a properly grounded
–
outlet only. See Grounding Instruc-
tion.
SAVE THESE INSTRUCTIONS

GROUNDING INSTRUCTIONS

This machine must be grounded. If it
should malfunction or breakdown,
grounding provides a path of least re-
sistance for electric current to reduce
the risk of electric shock. This machine
is equipped with a cord having an
equipment-grounding conductor and a
grounding plug. The plug must be in-
serted into an appropriate outlet that is
properly installed and grounded in ac-
cordance with all local codes and ordi-
nances.
WARNING
Improper connection of the equipment
grounding conductor can result in a risk
of electric shock. Check with a qualified
electrician or service person if you are
in doubt as to whether the outlet is
properly grounded. Do not modify the
plug provided with the machine-if it will
not fit the outlet, have a proper outlet
installed by a qualified electrician.
This machine is for use on a nominal
120-volt circuit and has a grounding at-
tachment plug that looks like the plug il-
lustrated in sketchpicture A. Make sure
that the machine is connected to an
outlet having the same configuration as
the plug. No adaptor should be used
with this machine.
CONNECT TO A PROPERLY
GROUNDED OUTLET ONLY
1 Grounded outlet
2 Grounded outlet Box
3 Grounded Pin
OPERATING SAFETY RULES
AND PRACTICES
Operator Responsibility
Safe operation is in the responsibility of
the operator.
The operator shall be familiar with the
operation and function of all controls
and instruments before undertaking to
operate the unit.
Before operating the unit, operators
shall have read and be familiar with the
operator's manual for the particular unit
being operated and they shall also
abide by the safety rules and practices
in the following paragraphs.
Before operating any unit, the operator
shall be familiar with unusual operating
conditions which may require addition-
al safety precautions or special operat-
ing instructions.
General
Before starting to operate the unit be in
operating position.
Do not start or operate the unit, any of
its functions or attachments, from any
place other than from the designated
operators position.
Before leaving the operator's position:
A bring the unit to a complete stop;
B if the unit must be on an incline,
block the wheels.
Maintain a safe distance from the edge
of ramps, platforms, and other similar
working surfaces.
Do not add to, or modify the unit.
Do not block access to fire aisles, stair-
ways or fire equipment.
Operator care of the unit
If the unit is found to be in need of re-
pair or in any way unsafe, or contrib-
utes to an unsafe condition, the matter
shall be reported immediately to the us-
er's designated authority, and the unit
shall not be operated until it has been
restored to safe operating condition.
If during operation the unit becomes
unsafe in any way, the matter shall be
reported immediately to the user's des-
ignated authority, and the unit shall not
be operated until it has been restored
to safe operating condition.
Do not make repairs or adjustments
unless specifically authorized to do so.
MAINTENANCE AND RE-
BUILD PRACTICES
Operation of the unit may be hazard-
ous if maintenance is neglected or re-
pairs, rebuilds, or adjustments are not
performed in accordance with the man-
ufacturer's design criteria. Therefore,
maintenance facilities (on or off pre-
mises), trained personnel, and detailed
procedures shall be provided.
Maintenance and inspection of the unit
shall be performed in conformance with
the following practices:
A a scheduled planned maintenance,
lubrication, and inspection system
shall be followed; consult the manu-
facturer's recommendations.
B only trained and authorized person-
nel shall be permitted to maintain,
repair, adjust, and inspect the unit,
and in accordance with manufactur-
er's specifications.
3
English