Recommended Lubricants; After The First 8 Hours Service; Every 20 Hours Service; Every 100 Hours Service - breviglieri mekfarmer 100v Utilisation Et Entretien

5 Roller bearing lubricator
6 Levelling bar screw lubricator
7 Gear housing:
(SAE 85W/140 oil)
Mekfarmer 100 version 200 ............................U.S.gal. 3.96
Mekfarmer 100 version 230 ............................U.S.gal. 4.49
Mekfarmer 100 version 250 ............................U.S.gal. 5.02
Mekfarmer 100 version 300 ............................U.S.gal. 5.55
The indicated quantities correspond to a level about 1 cm below
the upper edge of the gears in the casing when the machine is on
a flat surface.

5.2.1 RECOMMENDED LUBRICANTS

- For the mekfarmer 100 machine gearbox (1.1 litres), and for the
speed change of the mekfarmer 100v machine (1.7 litres), we
recommend: SAE 85W/140.
- LITHIUM GREASE type is recommended for all greasing points.
When servicing the driveline, strictly comply with the instruc-
tions given by the driveline Manufacturer, in the specific opera-
tion and maintenance manual with which each driveline is
equipped.

5.2.2 AFTER THE FIRST 8 HOURS SERVICE

Each new machine must be checked after the first 8 hours ser-
vice. proceed in the following way:
- Check the general condition of the machine.
- Fully tighten the blade screws after having checked the blades
themselves for wear.
- Check to make sure that all the bolts on the machine are tight.

5.2.3 EVERY 20 HOURS SERVICE

- Make sure that the blade screws are fully tightened.
- Grease the driveline, the roller adjuster screw and the roller
supports.

5.2.4 EVERY 100 HOURS SERVICE

- Check the level of the oil in the central distributor/reduction unit
housing. Top up if necessary.
- The level of the oil is correct when oil starts to come out (where
envisaged) of the hole in the oil drain cap (4 Fig. 10).

5.2.5 EVERY 500 HOURS SERVICE

- Change the oil in the central distribution/reduction unit hous-
ings after every 500 hours service or at least once a year.
- Check to make sure that the driveline clutch is fully efficient.
Have the clutch overhauled and the plates replaced by a spe-
cialized workshop if necessary.

5.3 PREPARING FOR STORAGE

Proceed with the following operations at the end of the season or
if the machine is to remain idle for a long period of time:
- Wash all fertilizers and chemical products from the machine
and dry it.
- Carefully check the machine and replace any damaged or worn
parts.
- Fully tighten all the screws and bolts, particularly the ones that
fix the tines.
- Thoroughly grease the machine and then cover it with a tarpau-
lin and store it in a dry place.
If these operations are carried out with care, it will be all to
the user's advantage as the machine will be in optimum con-
ditions when needed again.
If the machine must be dismantled, comply with the anti-pol-
mekfarmer 100v
lution laws in force. Old lubricants must and the various com-
ponents must be disposed of according to their different
structures.

5.4 SPARE PARTS

All the parts forming the machine can be ordered from the Manu-
facturer, specifying:
- The machine model.
- The serial number of the machine.
- The year of manufacture.
- The serial number of the required part (indicated in the spare
parts catalogue), a description of the part and the required quan-
tity.
- The means of transport. If this is not specified, the Manufac-
turer will dedicate diligent care to the service but shall not be
liable for delays in shipment due to causes of force majeure.
the shipping costs are always at the consignee's charge. The
goods travel at the purchaser's risk and peril even when sold
carriage paid.
Remember that the Manufacturer is always at your disposal
for any assistance and/or spare parts you may required.
- 25 -