(Micro Scrub / Ecs Machine); Brush Or Abrasive Disk From The Head; Mounting And Adjusting The Squeegee - Dustbane Hurricane 890 XTT Manuel D'opération

Masquer les pouces

Table des Matières

Les langues disponibles

• Speed potentiometer (fig. A, ref. 13): regulates the speed of the machine forwards

•

Emergency button (fig. A, ref. 10): acts as a safety device.

and backwards

•

Main Switch (fig. A, ref. 1): enables and disables the electrical power supply to all

• Speed potentiometer (fig. A, ref. 13): regulates the speed of the machine forwards

• Solution flow regulation button (fig. A, ref. 3): there are five operating modes

machine functions.

•

and backwards

Main Switch (fig. A, ref. 1): enables and disables the electrical power supply to all

•

STANDARD

•

Emergency button (fig. A, ref. 10): acts as a safety device.

machine functions.

• Solution flow regulation button (fig. A, ref. 3): there are five operating modes

•

AUTOMATIC

• Speed potentiometer (fig. A, ref. 13): regulates the speed of the machine forwards

•

Emergency button (fig. A, ref. 10): acts as a safety device.

•

STANDARD

and backwards

•

ECONOMY.

• Speed potentiometer (fig. A, ref. 13): regulates the speed of the machine forwards

•

AUTOMATIC

• Solution flow regulation button (fig. A, ref. 3): there are five operating modes

and backwards

•

MICROFIBRE (MICRO SCRUB / ECS MACHINE)

•

ECONOMY.

•

STANDARD

• Solution flow regulation button (fig. A, ref. 3): there are five operating modes

•

CHEM-DOSE

•

MICROFIBRE (MICRO SCRUB / ECS MACHINE)

•

AUTOMATIC

•

STANDARD

• Solution/concentrated detergent flow quantity variation buttons (fig. A, ref. 2):

•

CHEM-DOSE

vary the flow of solution/concentrated detergent

•

ECONOMY.

•

AUTOMATIC

• Solution/concentrated detergent flow quantity variation buttons (fig. A, ref. 2):

• Display (fig. A, ref. 6):

•

MICROFIBRE (MICRO SCRUB / ECS MACHINE)

•

ECONOMY.

vary the flow of solution/concentrated detergent

•

displays the quantity of concentrated detergent when enabled.

•

CHEM-DOSE

•

MICROFIBRE (MICRO SCRUB / ECS MACHINE)

• Display (fig. A, ref. 6):

•

displays alarm codes.

• Solution/concentrated detergent flow quantity variation buttons (fig. A, ref. 2):

•

CHEM-DOSE

•

displays the quantity of concentrated detergent when enabled.

vary the flow of solution/concentrated detergent

•

displays hour counter.

• Solution/concentrated detergent flow quantity variation buttons (fig. A, ref. 2):

•

displays alarm codes.

• Display (fig. A, ref. 6):

vary the flow of solution/concentrated detergent

• Horn button (fig. A, ref. 12):

•

displays hour counter.

•

displays the quantity of concentrated detergent when enabled.

• Display (fig. A, ref. 6):

• Suction button (fig. A, ref. 9): enables/disables the suction function. If you press this

• Horn button (fig. A, ref. 12):

button for more than five seconds, the suction motor starts working even without the

•

displays alarm codes.

•

displays the quantity of concentrated detergent when enabled.

• Suction button (fig. A, ref. 9): enables/disables the suction function. If you press this

operator on board.

•

displays hour counter.

•

displays alarm codes.

button for more than five seconds, the suction motor starts working even without the

• Brush button (fig. A, ref. 8):

• Horn button (fig. A, ref. 12):

operator on board.

•

displays hour counter.

•

STANDARD MACHINE, enables/disables operation of the head.

• Suction button (fig. A, ref. 9): enables/disables the suction function. If you press this

• Brush button (fig. A, ref. 8):

• Horn button (fig. A, ref. 12):

•

MICRO SCRUB / ECS MACHINE, enables/disables operation of the head. Hold

button for more than five seconds, the suction motor starts working even without the

• Suction button (fig. A, ref. 9): enables/disables the suction function. If you press this

•

STANDARD MACHINE, enables/disables operation of the head.

the button down for at least 3 seconds to select the operating mode, "BRUSH-

operator on board.

button for more than five seconds, the suction motor starts working even without the

•

MICRO SCRUB / ECS MACHINE, enables/disables operation of the head. Hold

PAD" with brushes/abrasive disk, or "MICROFIBRE" with microfibre disk.

• Brush button (fig. A, ref. 8):

operator on board.

the button down for at least 3 seconds to select the operating mode, "BRUSH-

• Solution tank level indicator: (fig. A, ref. 14): when there is not enough water in the

•

STANDARD MACHINE, enables/disables operation of the head.

• Brush button (fig. A, ref. 8):

PAD" with brushes/abrasive disk, or "MICROFIBRE" with microfibre disk.

solution tank, the LED comes on and the head and solenoid valve are turned off.

•

MICRO SCRUB / ECS MACHINE, enables/disables operation of the head. Hold

• Solution tank level indicator: (fig. A, ref. 14): when there is not enough water in the

•

STANDARD MACHINE, enables/disables operation of the head.

• Collection tank level indicator (fig. A, ref. 11): when the collection tank is full, the

the button down for at least 3 seconds to select the operating mode, "BRUSH-

solution tank, the LED comes on and the head and solenoid valve are turned off.

•

MICRO SCRUB / ECS MACHINE, enables/disables operation of the head. Hold

LED comes on and after a few seconds the suction motor is turned off.

PAD" with brushes/abrasive disk, or "MICROFIBRE" with microfibre disk.

• Collection tank level indicator (fig. A, ref. 11): when the collection tank is full, the

the button down for at least 3 seconds to select the operating mode, "BRUSH-

• Head pressure variation buttons (fig. A, ref. 7): vary the pressure of the brushes on

• Solution tank level indicator: (fig. A, ref. 14): when there is not enough water in the

LED comes on and after a few seconds the suction motor is turned off.

PAD" with brushes/abrasive disk, or "MICROFIBRE" with microfibre disk.

the floor

solution tank, the LED comes on and the head and solenoid valve are turned off.

• Head pressure variation buttons (fig. A, ref. 7): vary the pressure of the brushes on

• Solution tank level indicator: (fig. A, ref. 14): when there is not enough water in the

• Motor drive board indicator (fig. A, ref. 15): indicates the status of the motor drive

• Collection tank level indicator (fig. A, ref. 11): when the collection tank is full, the

solution tank, the LED comes on and the head and solenoid valve are turned off.

the floor

board (see section: "Motor drive alarm board").

LED comes on and after a few seconds the suction motor is turned off.

• Motor drive board indicator (fig. A, ref. 15): indicates the status of the motor drive

• Collection tank level indicator (fig. A, ref. 11): when the collection tank is full, the

•

Disk release button (fig. A, ref. 16): MICRO SCRUB / ECS MACHINE, enables

• Head pressure variation buttons (fig. A, ref. 7): vary the pressure of the brushes on

LED comes on and after a few seconds the suction motor is turned off.

board (see section: "Motor drive alarm board").

automatic release of the microfibre disk, brush or abrasive disk from the head.

the floor

•

Disk release button (fig. A, ref. 16): MICRO SCRUB / ECS MACHINE, enables

• Head pressure variation buttons (fig. A, ref. 7): vary the pressure of the brushes on

automatic release of the microfibre disk, brush or abrasive disk from the head.

• Motor drive board indicator (fig. A, ref. 15): indicates the status of the motor drive

the floor

6.2.

Mounting and adjusting the squeegee

board (see section: "Motor drive alarm board").

• Motor drive board indicator (fig. A, ref. 15): indicates the status of the motor drive

The squeegee (fig. B, ref. 6) is responsible for the first phase of drying.

•

Disk release button (fig. A, ref. 16): MICRO SCRUB / ECS MACHINE, enables

6.2.

Mounting and adjusting the squeegee

board (see section: "Motor drive alarm board").

automatic release of the microfibre disk, brush or abrasive disk from the head.

To mount the squeegee on the machine, proceed as follows:

•

Disk release button (fig. A, ref. 16): MICRO SCRUB / ECS MACHINE, enables

The squeegee (fig. B, ref. 6) is responsible for the first phase of drying.

1) insert the sleeve of the suction hose (fig. E, ref. 1) fully into the squeegee;

automatic release of the microfibre disk, brush or abrasive disk from the head.

To mount the squeegee on the machine, proceed as follows:

2) slacken the two knobs (fig. E, ref. 2) at the centre of the squeegee;

6.2.

Mounting and adjusting the squeegee

1) insert the sleeve of the suction hose (fig. E, ref. 1) fully into the squeegee;

3) insert the two threaded pins into the slots on the support (fig. E, ref. 3)

6.2.

Mounting and adjusting the squeegee

The squeegee (fig. B, ref. 6) is responsible for the first phase of drying.

2) slacken the two knobs (fig. E, ref. 2) at the centre of the squeegee;

4) fix the squeegee by tightening the two knobs (fig. E, ref. 2)

3) insert the two threaded pins into the slots on the support (fig. E, ref. 3)

To mount the squeegee on the machine, proceed as follows:

The squeegee blades scrape the film of water and detergent from the floor and prepare

The squeegee (fig. B, ref. 6) is responsible for the first phase of drying.

4) fix the squeegee by tightening the two knobs (fig. E, ref. 2)

1) insert the sleeve of the suction hose (fig. E, ref. 1) fully into the squeegee;

the way for perfect drying. With time, the constant rubbing makes the edge of the blade

To mount the squeegee on the machine, proceed as follows:

The squeegee blades scrape the film of water and detergent from the floor and prepare

2) slacken the two knobs (fig. E, ref. 2) at the centre of the squeegee;

in contact with the floor rounded and cracked, reducing the drying efficiency and requiring

1) insert the sleeve of the suction hose (fig. E, ref. 1) fully into the squeegee;

the way for perfect drying. With time, the constant rubbing makes the edge of the blade

3) insert the two threaded pins into the slots on the support (fig. E, ref. 3)

it to be replaced. The state of wear should be checked frequently.

2) slacken the two knobs (fig. E, ref. 2) at the centre of the squeegee;

in contact with the floor rounded and cracked, reducing the drying efficiency and requiring

For perfect drying, the squeegee must be adjusted in such a way that the edge of the rear

4) fix the squeegee by tightening the two knobs (fig. E, ref. 2)

3) insert the two threaded pins into the slots on the support (fig. E, ref. 3)

it to be replaced. The state of wear should be checked frequently.

The squeegee blades scrape the film of water and detergent from the floor and prepare

blade bends during operation by about 45° with respect to the floor at every point. Adjust