Upholstery Nozzle - Thomas COMPACT 20 Mode D'emploi

Paper filter bag
K Place the filter bag (34) inside the collecting bin (1),
making sure that the opening located in the
cardboard inlay (35) is placed in line with the
suction socket (8) .
Then press the filter bag (34) evenly around the
sides of the collecting bin (1) .
THOMAS paper filter bags are essential when
vacuuming fine dust, e .g . soot, ashes, sawdust or
cement . However, they are also recommended for
normal use, as they not only improve the retention
of dust, but also make filter changes more
hygienic .
Concentrated cleaning solution
Your THOMAS 4 in 1 contains 1 Liter of ProTex cleaning
concentrate . Please see bottle label for instructions for
use and dosage .
Use of tools and accessories
Reversible carpet + floor nozzle
This nozzle is suitable for vacuuming carpets and hard
floors, such as stone, parquet and synthetic tiles .
By means of the foot-operated lever, the nozzle can be
adjusted to suit the type of floor to be vacuumed:
- Vacuum smooth floors with the brush edge:
set the lever at the symbol
- Vacuum carpets with the smooth edge, i .e .
brush rim is retracted: set the lever at the
symbol .

Upholstery nozzle

Used for vacuuming upholstered furniture, mattresses,
and small uneven surfaces . The nozzle's thread
catcher also allows you to vacuum threads and fluff .
For easy handling the upholstery nozzle can also be
used with only one section tube, or directly on the
hose's grip .
Joint nozzle
Used for thoroughly vacuuming corners, grooves,
joints and other tight places . The joint nozzle can also
be directly attached to the grip .
Storage and transport
Set the control knob at "0" and pull out the plug .
Coil the mains cable loosely in the hand and hang it
over the notch in the carrying handle .
The suction tubes, complete with nozzle and flexible
hose, can be hooked into the fixtures at the back of the
appliance .
.
Dry vacuuming
Assembly
A Pull out the plug and lift off the motor
block (2) .
L Then push the cleaning solution tube (37), which is
located in the motor block (2), into the fixture
provided for this purpose (36) .
Inserting the filter
J Use the taper filter (25) in addition to the paper
filter sack . By doing this you achieve the best
retention of the residue dust . Place the taper filter
(25) on the underside of the motor head (2) .
Depending on the model in position 1 or 2 and
lock with the rotary clips . In the case of stubborn
dirt weak suction power the taper filter (25) can be
washed out with clear water without adding
washing detergents or cleaning agents . Make sure
that the filter is completely dry when using the
vacuum cleaner the next time .
K Place the filter bag (34) inside the collecting bin,
making sure that the opening located in the
cardboard inlay (35) is placed in line with the
suction socket (8) .
Then press the filter bag evenly around the sides
of the collecting bin .
D Put the motor block (2) back in position . The control
knob on the appliance must be set at "0" .
G Plug the appliance into a mains socket .
Switching on the appliance
M When using the appliance in the dry vacuuming
mode, the control knob (7) must be set at the
„carpet + floor nozzle" symbol .
The pilot lamp (6) should not be lit up.
The appliance is ready for use .
Wet vacuuming
Assembly
A Pull out the plug and lift off the motor
block (2) .
Warning! Always remove the filter unit before
vacuuming liquids, as it will otherwise become
unserviceable (see section "Changing the filter") .
L Always ensure that the float (38) is kept clean and
in good condition . It acts as a safety device and
automatically interrupts the flow of air when the
collecting bin is full .
15