Erreka VIVO-M203M Guide Rapide D'installation Et Programmation page 15

D1 D2 Parameter
C 0
Number of operators
1
Operator 1 turning direction
(operator 2 also changes)
2 Operator 2 turning direction
(operator 1 also changes)
3 Gate type
4 O p e n i n g s a f e t y
(photocell)
5
Closing safety device (photocell)
6 Electrolock / electromagnet
7
Encoder / Limit switches
The cabling depends on the type
of operator selected (C301,
C 3 0 2 o r C 3 0 3 ) ; s e e t h e
corresponding wiring diagram)
8
Radio card
9 Safety strip
A Slowdown
P 1 T o t a l o p e n i n g
programming
2
P e d e s t r i a n o p e n i n g r a d i o
programming
3
Programming gate travel
F 1
Key command by way of ST1
and ST2 pushbuttons
2
A u t o m a t i c o r s t e p - b y - s t e p
operation mode and standby
time (in seconds) in automatic
mode
3 Pedestrian opening (%)
4
Pedestrian closing mode
Complete programming chart (I)
Default
D3 D4
option
0 1, 2
0 1, 2
0 1, 2
0 1 ... 3
d e v i c e 0,1 0,1
0,1 0,1
0 0...4
0 0...5
0 1, 2
0 1, 2
0 0...3
r a d i o o ç
o ç
o ç
0 0...4
0..5. 0...9
0...9 0...9
0 1, 2
Options or values
01 01: one operator,
02: two operators (only available with C301)
01 01: direction A,
02: direction B
01 01: direction A,
02: direction B
01 01: swing,
02: sliding,
03: up-and-over
00 00: not installed,
10: no testing,
11: with testing
00 00: not installed,
10: no testing,
11: with testing
00 00: not installed
01: electrolock without reverse impulse
02: electrolock with reverse impulse
03: electromagnet without impulse
04: drop electromagnet
00 00: not installed;
01: with single encoder;
02: with limit switches;
03: with dual encoder;
04: with encoder and limit switches (not available
with C301 selected);
05: VULCAN VUS and ATLAS (ATS) G6xxI (only
available with C301 or C303 selected)
02 01: RSD card (no decoder);
02: two channel decoder card
01 01: mechanical;
02: resistive 8k2
02 00: no slowdown;
01: slowdown in opening and closing;
02: slowdown in opening;
03: slowdown in closing
Programmes total opening channel and code
Programmes pedestrian opening channel and code
Programmes the operations in accordance with the
configuration CA
01 00: ST1 and ST2 without effect, the key commands
are given by radio (channel 1: total opening-
closing, channel 2: pedestrian opening-closing)
01: ST1 total opening-closing, ST2 pedestrian opening-
closing
02: ST1 total opening, ST2 total closing
03: dead-man mode (the display shows HP.);
04: dead-man mode in closing
00 00: step-by-step mode
01: automatic mode and standby time 1 second;
...
59: automatic mode and standby time 59 sec.;
1.0: 1 min. 0 sec.;
...; maximum 4 minutes
40 00: pedestrian opening is not carried out,
10: 10% of total opening,
etc
02 01: automatic (only with F2 K 00), taking the time
set in F2XX as the value;
02: step-by-step
15