Erreka VIVO-M203M Guide Rapide D'installation Et Programmation page 11

ST2
ST1
ST1: open
ST2: close
A1
E1
P13 P14 P15 P16
ENCODER 1
A1
E1
P13 P14 P15 P16
ENCODER 1
E1
P13 P14 P15 P16
ENCODER 1
Operator connection
Single encoder
connection (C701)
E1 connector:
V+: red cable
GND: white cable
SGN1: green or blue
cable
SGN2: do not connect SGN2: closing (FCC)

In sliding (C302) and up-and-over doors (C303), it is only possible to use a single motor (M1),
which should be connected to the "MOTOR 1" terminals.
When using a single encoder (C701, C704) or dual encoder (C703), always connect to the
"ENCODER 1" terminals.
When using limit switches (C702, C704 or C705), always connect to the "ENCODER 2" terminals.
Operator cabling for sliding and up-and-over doors
(parameters C302 and C303)
P24 P25
P17 P18 P19 P20
P13 P14 P15 P16
ENCODER1 ENCODER2
P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12
P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12
C701
E2 E1
P13 P14 P15 P16
ENCODER 2
C703
A1
E2
E1
P13 P14 P15 P16
ENCODER 2
C705
A1
ATS NA
E2
P13 P14 P15 P16
ENCODER 2
Limit switch
connection (C702)
E2 connector: E1 connector:
V+: do not connect V+:
GND: common (COM) GND: white cable
SGN1: opening (FCA) SGN1: green or blue
SGN2: purple cable
EDGE
F1
P21 P22 P23
-FT
AUX
(Test)
24 Vdc
MAX. 3A
G7 G8
G9 G10 G4
MOTOR2
C702
A1
E2
P13 P14 P15 P16 P13 P14 P15 P16
ENCODER 1 ENCODER 2
C704
A1
E2
P13 P14 P15 P16 P13 P14 P15 P16
ENCODER 1 ENCODER 2
E2 connector:
V+:
GND: common (COM)
SGN1: ATS operator safety micro and NA
SGN2: bridge to GND
Dual encoder
FC and single encoder connection (C704)
connection (C703)
E1 connector:
red cable V+:
GND: white cable
SGN1: green or blue
cable
SGN2: do not connect SGN2: closing (FCC)
F3
F4
MAX. 3A
CN13
G5 G6 G1 G2 G3 N L
N L
POWER - 230V
POWER - 230V
MOTOR1
A1
MAX. 3A
A1: Operator 1
E1: "ENCODER 1" terminals
E2: "ENCODER 2" terminals
ATLAS connection (ATS) G6xxI (C705)
do not connect
closing micro (parallel connection)
E2 connector:
red cable V+:
GND: common (COM)
SGN1: opening (FCA)
cable
VIVO-M203:
230V, 50Hz
VIVO-M203M:
125V, 60Hz
P241Z4
M o t o r
connection
G1/G4: open
G2/G5: close
G3/G6: common
do not connect
11