Operating The Tool - Stanley FME380 Mode D'emploi

Use
Warning! Let the tool work at its own pace. Do not overload.
Note:Before engaging the on/off switch, check the saw blade
Tighten clamp (3)
For an optimal quality cut, the saw blade should not
Be aware that the actual depth of cut of the diamond
Note: Always make trial cuts first to verify actual line of
connect vacuum cleaner hose (19) to connection (13) and
Warning! Never let the vacuum cleaner hose interfere with
Warning! Do not use vacuum cleaner when cutting metal.
Warning! Before changing blades or performing any mainte-
nance, ensure the tool is off and disconnected from the power
Set cutting depth to the maximum (fig. D).
Press button (10) with your thumb
Switching on and off (fig. A)
to see if it is fitted properly and runs smoothly, and the blade
clamp screw is well tightened.
Push the trigger lock and shoe release button button (10)
u
to release the trigger.
Switch on tool by pulling trigger switch (1).
u
Switch off tool by releasing trigger switch (1).
u
Adjusting cutting depth (0-28,5 mm) (fig.B)
Loosen clamp (3).
u
Set desired cutting depth using scale (2).
u
u
u
extend more than 3 mm below the workpiece
u
disc differs approx. 2 mm from the depth of cut indicated
on scale (2).
cut.
Dust suction (fig.C)
u
vacuum cleaner as illustrated.
the lower guard or the cutting operation.
Changing saw blade (fig. D - G)
source.
u
Use hex key (15) provided.
u
Push spindle-lock button (14) and hold (Fig. E).
u
Remove blade bolt (9) by turning hex key (15)
CLOCKWISE (= in same direction as arrow imprinted on
the guard) (Fig. F).
Release spindle-lock button (14).
u
Remove flange (8).
u
u
Lift up foot (7) and remove saw blade.
u
Install new blade making sure that rotation of blade is in
u
same direction as arrow imprinted on the guard.
Mount flange (8).
u
Firmly tighten blade bolt (9) by turning hex key (15)
u
COUNTER-CLOCKWISE while pushing spindle-lock
button (14).
Release spindle-lock button (14).
u

Operating the tool

Electronic Function. Laser beam action (Fig.I)
Cleaning of the lens for the laser light
(Original instructions)
Tilt tool forward with line-of-cut indicator (20) lined up with
The tool should run at full speed before the blade enters
Do not force the tool (apply light and continuous
pressure in order to avoid overheating the blade tips and,
After completing the cut switch off tool by releasing trigger
Ensure that the blade has come to a complete standstill,
Caution! When not in use, be sure to turn off the laser.
Before shifting the laser line or performing maintenance
heres to it in such a way that the laser line is no longer easily
visible, unplug the saw and clean the lens carefully with a
Note: When laser line is dim and almost or entirely invisible
because of the direct sunlight in the indoor or outdoor window
Note: All of the adjustments for the operation of this machine
Caution: Use of controls or adjustments or performance of
(fig. H - M)
Set desired cutting depth.
u
Connect plug to power source.
u
Press button (10) with your thumb.
u
Place tool with front end of foot flat on workpiece.
u
u
desired line of cut marked on the workpiece (fig. H).
Ensure that the saw teeth are not engaged into the work-
u
piece.
Switch on the tool.
u
u
into the workpiece.
u
in case of cutting plastics, melting the plastic material).
While working, always hold the tool at the insulated grip
u
area(s).
u
(1).
u
before you lift the tool from the workpiece.
Never look into the laser beam directly; laser beam may injure
your eyes.
LASER RADIATION: DO NOT STARE INTO THE BEAM or
any CLASSII LASER PRODUCTS.
adjustment, be sure to unplug the tool.
To turn the laser on/off, toggle the switch (12a) on the
u
back of the laser housing.
If the lens for the laser light becomes dirty, or sawdust ad-
damp, soft cloth. Do not use solvents or any petroleum based
cleaners on the lens.
near your work area, relocate the work area to a place not
exposed to direct sunlight.
have been carried out at the factory.
procedures other than those specified herein may result in
hazardous radiation exposure. The use of optical instruments
with this product will increase eye hazard. Do not attempt to
repair or disassemble the laser. If unqualified persons attempt
to repair this laser product, serious injury may result.
ENGLISH
11