Further Safety Instructions For All Saws; Lower Guard Function; Kickback Causes And Related Warnings - Stanley FME380 Mode D'emploi

Further safety instructions for all saws

Kickback causes and related warnings

misaligned saw blade, causing an uncontrolled saw to
closing down, the blade stalls and the motor reaction
if the blade becomes twisted or misaligned in the cut,
top surface of the wood causing the blade to climb out
position your arms to resist kickback forces. Position
your body to either side of the blade, but not in line
with the blade. Kickback could cause the saw to jump
When blade is binding, or when interrupting a cut
for any reason, release the trigger and hold the saw
motionless in the material until the blade comes to a
complete stop. Never attempt to remove the saw from
the work or pull the saw backward while the blade is
in motion or kickback may occur. Investigate and take
When restarting a saw in the workpiece, centre the
saw blade in the kerf and check that saw teeth are
not engaged into the material. If saw blade is binding, it
Support large panels to minimise the risk of blade
pinching and kickback. Large panels tend to sag under
panel on both sides, near the line of cut and near the edge
Do not use dull or damaged blades. Unsharpened or
Blade depth and bevel adjusting locking levers
must be tight and secure before making cut. If blade
Use extra caution when sawing into existing walls or
other blind areas. The protruding blade may cut objects
kickback is a sudden reaction to a pinched, bound or
u
lift up and out of the workpiece toward the operator;
when the blade is pinched or bound tightly by the kerf
t
drives the unit rapidly back toward the operator;
t
the teeth at the back edge of the blade can dig into the
of the kerf and jump back toward the operator.
Kickback is the result of tool misuse and/or incorrect operating
procedures or conditions and can be avoided by taking proper
precautions as given below.
Maintain a firm grip with both hands on the saw and
u
backwards, but kickback forces can be controlled by the
operator, if proper precautions are taken.
u
corrective actions to eliminate the cause of blade binding.
u
may walk up or kickback from the workpiece as the saw is
restarted.
u
their own weight. Supports must be placed under the
of the panel.
u
improperly set blades produce narrow kerf causing exces-
sive friction, blade binding and kickback.
u
adjustment shifts while cutting, it may cause binding and
kickback.
u
that can cause kickback.

Lower guard function

Saw blades
Safety of others
Residual risks
(Original instructions)
Check guard for proper closing before each use. Do
not operate the saw if guard does not move freely
and enclose the blade instantly. Never clamp or tie
the guard so that the blade is exposed. If saw is ac-
sure that guard moves freely and does not touch the blade
Check the operation of the lower guard spring. If the
guard and the spring are not operating properly, they
must be serviced before use. Lower guard may operate
sluggishly due to damaged parts, gummy deposits, or a
The lower guard may be retracted manually only for
special cuts sucha as "plunge cuts" and "compound
cuts". Raise the lower guard by the retracting handle
and as soon as the blade enters the material, the
lower guard must be released. For all other sawing, the
Always observe that the lower guard is covering the
Do not use blades of larger or smaller diameter than
Warning! Never use abrasive wheels.
This tool can be used by children aged from 8 years and
above and persons with reduced physical, sensory or
they have been given supervision or instruction concern-
ing use of the appliance in a safe way and understand the
maintenance shall not be made by children without super-
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
u
cidentally dropped, guard may be bent. Check to make
or any other part, in all angles and depths of cut.
u
build-up of debris.
u
lower guard should operate automatically.
u
blade before placing the saw down on bench or floor.
An unprotected, coasting blade will cause the saw to walk
backwards, cutting whatever is in its path. Be aware of
the time it takes for the blade to stop after the switch is
released.
u
recommended. For the proper blade rating refer to the
technical data. Use only the blades specified in this
manual, complying with EN 847-1.
u
u
mental capabilities or lack of experience and knowledge if
hazards involved.
Children shall not play with the tool. Cleaning and user
u
vision.
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
risks can not be avoided. These include:
Injuries caused by touching any rotating/moving parts.
u
ENGLISH
9