IKRA ELM 1200 U Manuel D'utilisation page 19

Assembly
This manual gives instructions on the correct assembly
and safe use of your machine. It is important that you read
these instructions carefully.When fully assembled the ma-
chine weighs approximately 10 kg. If necessary, obtain
assistance to remove from packaging. Take care when
carrying the mower to the lawn, as the blades are sharp.
Delivered Items
Carefully remove the machine from its packaging and
check that you have all the following items:
Lawnmower with handle assembly
• 2 Handles bottom
• 2 Bolts
• 2 Knob module
• 2 Screws
• Grass box
• Grass box cover
• Tongue
• 2 Cable clips
If bolts parts are missing or damaged, please contact
the consumer care hotline for assistance.
Assembly of switch box (fig. 1 - 5)
1. Before using the lawn mower, you need to assemble
the switch box on handle lever as show in photo 5.
2. Align the groove of switch box to the guide rail, slide
the switch box toward the rear handle. (fig. 2 + 4)
3. Only with clips on switch box (fig. 3) located in posi-
tion to lock the switch box on handle lever as well as
the assembly indication line (fig. 4) aligned, then the
switch box assembled.
4. After fixing, move the switch box in reverse direction
to check if the switch box assembled in position or
not.
Assembly (fig. A)
Important! Before you assemble the lawn mo-
wer, check the accessories according above
information, make sure the accessories are
completed.
1. Insert the lower handles 6 into the holes provided in
the deck, secure with the screws (A1).
2. Attach the cable strain relief 4 to the upper handle
3 (A2).
3. Attach the upper handle 3 with bolts and knob module
5 to the lower handles 6 (A3).
4. The upper handle 3 is height adjustable. Handles can
be fixed in desired position I or II (A3).
Note: Ensure that the cable clips 12 are used to fix the
cable to the handle.
Attach cable to cable strain relief 4 ensuring that sufficient
cable slack is available. (not for GB models)
Ensure cables are not trapped when folding/unfolding top
handles. Do not drop the handles.
GB | Operating Instructions
Assembly of Grass box (fig. B)
1. Assemble the grip onto the upper cover of the catcher
2. Slide the grass box tongue into the slots in the grass
3. Starting at the rear of the grass box, locate the grass
4. Fitting assembled grass box to lawn mower (B4):
Note: For non grass collection the mower can be used
without the grass box in position, with the safety guard 8
in the down position.
Adjusting the Cutting Height
Height of cut is adjusted by raising or lowering the Front
and Rear wheels. (C1&C2&C3)
Adjusting the cutting height: Pull the wheel axle forwards
(arrow 1). Put the axle in the desired height (arrow 2). The
wheel axle locked by the spring power.
There are three heights of cut on this product.
NOTE
A medium height of cut is recommended for most lawns.
The quality of your mowing will suffer and collection will
be poor if you cut too low.
HEIGHT OF CUT
Low
(Low to Medium)
Medium
(Medium to High)
High
Starting and Stopping
Start:
• Press and hold the safety button 2. Squeeze the
5
(B1)
box lower until it clicks securely into position. (B2)
box cover into the grass box by sligning the clips. En-
sure all clips are correctly located. (B3)
a) Lift the safety guard 8 (B4-a).
b) Make sure the discharge chute is clean and free
from debris.
c) Locate fully assembled grass box 7 onto location
points at the rear of the deck as illustrated (B4-b).
d) Locate safety flap onto the top of the grass box.
Ensure the grass box is easy located.
Warning: release switch lever 1 and wait until the
motor stops before adjusting height. The blades
continue to rotate for a few seconds after the ma-
chine is switched off, a rotating blade can cause
injury.
Make sure the blade stopped rotating before
switching "on" again.
Do not rapidly switch on and off.
switch lever 1 towards the handle (D).
(fig. C)
WHEELS POSITION
Front position 20 mm
Rear position 20 mm
Front position 20 mm
Rear position 40 mm
Front position 40 mm
Rear position 40 mm
Front position 40 mm
Rear position 60 mm
Front position 60 mm
Rear position 60 mm
(fig. D)