Other Functions - Krups EA815 Mode D'emploi

Rinsing the circuits :
Press the maintenance and settings button
nance button .
If necessary, using the navigation button,
Press START , rinsing starts and finishes when the coffee menu appears.
Automatic rinsing of the circuits when the machine starts.
You can choose to program the machine to be rinsed automatically each time it is turned on. To do this,
press the maintenance and settings button
rinsing programming symbol . Press the
press the , button, automatic rinsing is disabled.
You can return to the coffee types menu by pressing the
Warning: after this rinsing process, hot water will be released from the coffee outlet. Ensure that the drip
tray is in place even when the machine is not being used. The cycle lasts only a few seconds and stops au-
tomatically.
Cleaning program - total duration: approximately 13 minutes
You do not have to run the cleaning program as soon as the appliance requests it, but it must be done rea-
sonably soon after. If cleaning is postponed, the alert message will remain illuminated until the process is car-
ried out.
When the symbol lights up, you can run the automatic cleaning program by pressing the maintenance
and settings button . The symbol is selected. The function indicator
maintenance button .
The automatic cleaning program is divided into 2 stages: the cleaning cycle itself, followed by the rinse cycle.
You can clean the machine at any time by pressing the maintenance and settings button
navigation button select the cleaning symbol
To run this cleaning program, you will need a container which holds at least 20 oz and which can be placed
beneath the coffee outlet and the steam nozzle. The
Lift the cup tray fig.28.
Insert the KRUPS cleaning tablet fig.29.
Fill the water container to its maximum level of 57 oz fig.2.
Empty the coffee grounds collector and the drip tray and clean the coffee drawer fig.23-24-25.
Put a 0.6 L (21 oz) container under the coffee and steam jets fig.30.
Press START . The symbol becomes constant. The first phase (approximately 10 minutes) begins.
When this phase has finished, empty the container and the drip dray. The
back in place.
Press START . The symbol becomes constant, the final phase (approximately 3 minutes) begins.
When this phase has finished, empty the container and the drip tray. The cycle has finished, the coffee
types menu appears.
Note: if you turn off or unplug your machine during cleaning or if there is a power failure, the cleaning program
will start from the beginning of the program once the power is restored to the appliance. It is not possible to
postpone this process. It is obligatory in order to rinse the water circuit. In this case, a new cleaning tablet
may be necessary. It is best to run the full cleaning program in order to avoid any risk of poisoning. The
cleaning cycle is irregular: do not put your hands under the coffee outlet while the cycle is running.
Descaling program - duration: approximately 20 minutes
You do not have to run the descaling program as soon as the appliance requests it, but it must be done rea-
sonably soon after. If descaling is postponed, the alert message will remain illuminated until the process is
carried out.
The amount of limescale collected depends on the hardness of your water.
Warning: if your product is fitted with our Claris - Aqua Filter System cartridge, remove the cartridge before
descaling.
3
fig.27. The function indicator is shown above the mainte-
select the rinse symbol .
fig.27. Using the navigation button , select the automatic
button to choose ON which confirms this program. If you
button.
is shown above the
.
symbol flashes.
symbol flashes. Put the parts
When the
and settings button
symbol flashes and the function indicator
To run the descaling program, you will need a container which holds at least 20 oz and KRUPS descaling
powder.
Fill the water tank up to the CALC mark then pour in the contents of one packet fig.31.
Put a 20 oz container under the coffee and steam nozzles.
Press START
this phase has finished, empty the container and the drip dray. The
clean the water tank using a sponge.
Once clean, refill your water tank and replace all parts. The
Press START
When this phase has finished, empty the container and the drip tray. The
Press START
this phase has finished, empty the container and the drip tray. Descaling is complete.
Note : if you turn off or unplug your machine during descaling or if there is a power failure, the cleaning
program will start from the beginning of the program once the appliance is restarted. It is not possible to
postpone this process. It is obligatory in order to rinse the water circuit. Running the descaling program is
advisable. The descaling cycle is irregular: do not put your hands under the steam outlet.
Once the cycle has finished, the coffee types menu appears.

OTHER FUNCTIONS

You can access the appliance's OTHER FUNCTIONS menu by pressing the maintenance and settings
then, using the
button .
For all settings, use the navigation button
To exit out of the maintenance and settings menu, press the
MAINTENANCE
All of the following options allow you to run the selected programs:
symbol lights up, you can run the automatic descaling program by pressing the maintenance
fig.27. If necessary, using the navigation button,
is located above the maintenance button
to begin the first phase (approximately 8 min). The
to begin the second phase (approximately 6 min). The
to begin the final phase (approximately 6 min). The
and + or –
Allows you to access rinsing.
Allows you to access cleaning.
Allows you to access descaling when the appliance requests it.
Allows you to prime the filter (Claris cartridge).
Return to coffee types menu.
select the symbol. The
.
symbol becomes constant. When
and symbols flash. Remove and
symbol disappears.
symbol becomes constant.
symbol flashes.
symbol becomes constant. When
for the options.
button.
31