Krups EA815 Mode D'emploi page 19

TURNING OFF YOUR APPLIANCE
You can turn off your appliance at any time. When stopped, the machine emits a double beep and OFF is dis-
played on the screen. The appliance has registered your request and will stop as soon as possible.
SETTINGS
All of the following options allow you to run the selected programs:
You can set your water hardness between 0 and 4.
See "Measuring water hardness" (below) by pressing the + or –
.
buttons
You can program automatic rinsing each time the appliance is
turned on by pressing the
You can choose the period after which your appliance will turn
off automatically (between 15 and 120 minutes by pressing the
buttons).
You can adjust the temperature of your coffee to three different
levels by pressing the
You can choose between oz and ml by pressing the + or –
oz ml
.
buttons
Return to coffee types menu.
Measuring water hardness
It is advisable to adjust the appliance according to the hardness of the water used. To check the water hard-
ness, use the stick supplied with your machine or contact your local water authority.
Degree of Classe 0 Classe 1
hardness Very soft Soft
° dH < 3° > 4°
° e < 3.75° > 5°
° f < 5.4° > 7.2°
Appliance
0 1
settings
Installing the filter (Claris - Aqua Filter System cartridge) fig.32
Note : To correctly install your cartridge, ensure that you follow the installation procedure each time you replace
it.
Fig.33. A mechanism which memorizes the month in which the cartridge was changed and replaced (after a
maximum of 2 months): set the date using the cartridge cursor. Fit the cartridge in the tank fig.34. In the main-
tenance and settings menu , the function indicator
Using the navigation button , select the filter cartridge installation symbol
start button start to flash.
32
buttons and selecting ON.
buttons.
Classe 2 Classe 3 Classe 4
Average hardness Hard Very hard
> 7° > 14° > 21°
> 8.75° > 17.5° > 26.25°
> 12.6° > 25.2° > 37.8°
2 3
is located above the maintenance button
. The symbols and the
Place a 21 oz container under the steam nozzle.
Press start . The start-up cycle begins and finishes when the coffee types menu appears
TROUBLESHOOTING
If one of the problems described in the table persists, contact KRUPS customer service.
PROBLEM MALFUNCTION
Your machine detects a fault: a
symbol appears.
The appliance does not turn on
when the button is pressed.
The coffee grinder makes a
strange noise.
The steam nozzle makes a noise.
The steam nozzle on your
machine seems partially or
completely clogged.
The steam nozzle makes little or
no milk froth.
No steam comes out of the
nozzle.
The auto-cappuccino accessory
makes little or no froth.
The auto-cappuccino accessory
does not take in milk.
There is water underneath the
4
appliance.
After emptying the coffee
grounds collector and cleaning
the coffee drawer, the warning
message is still displayed.
.
CORRECTIVE ACTION
Switch off and disconnect the machine, remove the filter cartridge, wait for a minute
and restart the machine.
Check your fuses and plug sockets.
Check that the two power plugs are pushed in properly both on the appliance and at
the socket.
There is a foreign object in the grinder. Disconnect the machine before investigating.
See if you can extract the foreign object using your vacuum cleaner.
Check that the steam nozzle is correctly attached to its corresponding end piece.
Ensure that the opening in the end piece is not obstructed by milk residue or
limescale. Unclog the holes with the needle supplied with your appliance.
The milk temperature is too high. For milk-based drinks, you use cold (39°F) pasteu-
rised or UHT milk. It is also advisable to use a cold container. If the results do not
improve, try changing the brand of milk.
Empty the tank and temporarily remove the filter cartridge. Fill the water tank with
mineral water which is high in calcium (> 100 mg/l) and run successive steam
cycles.
Check that the accessory is correctly attached to the appliance, remove it then
replace it.
Check that the flexible tube is not obstructed or pierced and that it is correctly
attached to the accessory so as to make it airtight. Rinse and clean the accessory
(refer to the "Auto-cappuccino accessory" chapter).
Before removing the water tank, wait for 15 seconds after the coffee has finished
flowing so that the machine finishes its cycle properly.
Check that the drip tray is correctly positioned on the machine; it should always be
in place, even when the appliance is not in use.
Check that the drip tray is not full.
The drip tray should not be removed during a cycle.
Correctly replace the coffee drawer and the coffee grounds collector, follow the
instructions on the screen.
Wait at least for 4 seconds before replacing them.
33