Programming Recirculation (Optional); Intouch - Novy Fusion Pro 8710 Mode D'emploi

When switching the lighting on it will always go to full
power and can also be used when the fan is switched off.
Dimming the LED lighting
When the LED lighting is switched on you can dim it by
keeping key pressed.
4

2.4 Programming recirculation (optional)


If recirculation is selected programming must
take place once.
This programming function activates the replacement
indicator of the monobloc recirculation fi lter and the delay
time is changed.
Activating programming
− The motor must be switched off
− Press the and the
2
seconds until the red LED fl ashes 5 times.
The following functions then operate:
− Replacement indicator of the monobloc fi lter is activated.
After a set time a red indicator light on the appliance
shows that the monobloc fi lter must be replaced.
− The delay time is set to 30 minutes (instead of the default
10 minutes).

Use the delay time of 30 minutes so the
cooking odours can be properly removed in
the monobloc fi lter.
Read paragraph 3.4 for more information about replacement
of the monobloc recirculation fi lter.
Deactivating programming
− The motor must be switched off
− Press and at the same time for 3 seconds until
2 3
the 3rd green LED fl ashes 3 times.
The delay time is again set to 10 minutes (instead of 30 min-
utes) and cleaning indicator for recirculation is switched off.

2.5 InTouch

The cooker hood has the InTouch function. If you have an
induction hob from Novy with InTouch, you can operate
the extraction hood from the hob.
Visit the website for the different models of induction hobs
with InTouch.
keys at the same time for 3
3
Turning the InTouch function on and off


The InTouch function is off by default. To con-
nect the cooker hood to a Novy induction hob
with InTouch, the InTouch function must fi rst be
switched on on the cooker hood.
The InTouch function is off by default. The function can be
switched on by pressing the
time for 3 seconds.
The 2nd and 3rd LEDs fl ash 3 times to confi rm (the appli-
ance must be switched off).
To switch the InTouch function off press the
keys at the same time for 3 seconds and the 2nd and 4th
LEDs fl ash 3 times to confi rm. (The appliance must be
switched off). switched off).


Turning off the InTouch function on the cooker
hood results in the connection between cooker
hood and Novy induction hob with InTouch and/
or remote control is also disabled.
Programming InTouch on the induction plate
− Connect the plate to the mains supply.
− Touch simultaneously the keys
plate until you hear a beep signal (prox. 7 sec.).
− The cooker plate now searches automatically for the
hood code.
− Wait until the cooker hood illumination begins to fl ashing
OR you hear a "click" sound when you have an extractor
hood without lighting (Be patient, this can betake a while).
− Does the light blink or you hear the "click" sound; press
immediately on any InTouch key or
on the induction hob.
− You will hear a "beep" signal to indicate the link between
the two devices.
Now you can operate the hood with the keys on the in-
duction plate.
You can fi nd more information about using the InTouch
functions in the InTouch manual for the hob.
The InTouch function between cooker hood and hob works
with a fi xed code.
If the set code disrupts other transmitters, another code
can be selected. There are 10 different codes.
A remote control is required to change the code.
More information on reprogramming with the remote control
can be found in the manual of the remote control.

You can obtain a remote contol from a dealer or
the Novy website.
Article number remote control : 840.029.
– 30 –
and keys at the same
1
3
1 and
2
and on the induction
or or or