Parameter Menu - Lowara Q-Smart Manuel D'installation, D'exploitation Et De Maintenance


SE: Sewage

bS: Pressurisation (booster)
5. Press (5) to confirm
6. 1P or 2P are shown on the display.
7. Press (1) or (2) to edit the number of pumps:

1P= one pump

2P= two pumps
8. Press (5) to confirm
9. Turn the control panel off and then on again.
The new application is now activated.
5.4.4

Parameter menu

Only in STANDBY mode (StY) is it possible to select
the operation parameters (see
NOTICE:
After 3 minutes of inactivity and if no button is
used, automatic mode is restored.
The pump remains in standby during configuration.
Refer to figures 1 and 2
1. Press and hold (4) to access STANDBY (StY)
mode.
2. LEDs (2) and (5) switch off. LED (9) is ON.
3. Press (5) to access the parameter menu.
"000" flashes.
4.
5. Press (1) or (2) to edit the password 066.
6. Press (5) to confirm. If password is wrong press
(4) for read-only mode.
7. Press (1) and (2) to view the parameter
8. Press (5) to edit the parameter. It flashes.
9. Press (1) or (2) to modify the value.
10. Press (5) to confirm.
11. Press (1) or (2) to confirm and move on to the
next parameter or press (4) for AUTOMATIC or
MANUAL mode.
12. Repeat points 7 to 9.
13. Press (4) for AUTOMATIC or MANUAL mode.
Tab 2 SEWAGE Application
(parameter SE is selected, section 5.4.3)
Par. Description Range
SYSTEM
c01 Number of 1= 1 pump
pumps 2= 2 pumps
c02 Filling func- 0= Disabled
tion. 1= Enabled
(See Fig-
ures 48 to
52 and 58 to
62)
c03 Type of 1= Float
sensor that switches
is used. 2= Sensor
level
Tab 2 or Tab 3).
Unit Default
- depend-
ing on the
control
panel
model
- 0
- 1
3= Probes
4= Level
sensor with
automatic
switching to
float if sen-
sor is faulty
5= Level
sensor with
automatic
switching to
probes if
sensor is
faulty
c04 Sensor sig- 1= 4-20mA
nal type 2= 0-20mA
c05 Initial scale Pressure:
value of the 0 to 60 bar
sensor. Only Tempera-
if sensor is ture:
used. -20 to 100°C
Level:
0 to 50 m
r05 Calibration 0= Disabled
of the initial 1= Enabled
scale in mA.
t05 Software Standard
filter for ana- Lowara
logue input
c06 Full scale Pressure:
value of the 0 to 60 bar
selected Tempera-
sensor. Only ture:
if sensor is -20 to 100°C
used. Level:
0 to 50 m
THRESHOLD AND TIMING (threshold is active
only with sensor)
c07 Unique level 0= Disabled
set point 1= Enabled
r07 Set point 0 to Full
level value Scale
r08 Upper 0 to Full
threshold Scale
delta
r09 Lower 0 to Full
threshold Scale
delta
r10 Upper 0
threshold Scale
Start Pump
1
t10 Delay time 0 to 100
start Pump 1
r11 Lower 0
threshold Scale
Stop Pump
1
t11 Delay time 0 to 100
stop Pump 1
r12 Upper 0
threshold Scale
en - Original instructions
- 1
vari- 0
ous
- 0
- 3
Vari- 10.0
ous
- 0
Vari- 5
ous
Vari- 0.5
ous
Vari- 0.5
ous
to Full Vari- 8
ous
sec 0
to Full Vari- 2
ous
sec 0
to Full Vari- 7
ous
41