Télécharger Imprimer la page

Witter VL46AU Notice De Montage

Volvo xc70 2007-actuel

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

Fitting
Instructions
MATERIALS
A
1
Cross Bar.
B
2
Captive Nut Straps.
C
4
M12 x 50 x 1.75 pitch Bolts, Lock Washers and Flat Washers.
D
1
Electrical Plate Assembly.
E
1
Electrical Plate Bracket.
F
2
M12 x 100 x 1.75 pitch Bolts and Nyloc Nuts. (Grade 10.9)
G
2
Spacers.
D
1
Electrical Plate.
ZF
1
Neck with European facing to 94/20 EC A50-1
FITTING
1. Remove bumper (4 wheel arch screws each side, 2 plastic nuts in bottom edge and unclip corners and sides from
vehicles and pull rearwards).
2. Remove crash beam and loosen or remove threaded towing eye bush by un-screwing its centre bolt located under a
bracket in the boot rear panel.
3. Lower exhaust silencer to make access to the towbar mountings easier.
4. Remove sealing tape from sides of chassis rails to expose towbar mounting holes (B).
5. Insert Cross Bar (A) into chassis rails and secure with fasteners (C) and Captive Nut Straps (B). Note: Due to the
narrow width of the openings in the rear panel insert the Nut Straps (B) into chassis before assembling Cross
Bar (A).
6. Assemble Neck (ZF) and Electrical Plate Bracket (E) to Cross Bar using fasteners (F) and Spacers (G).
7. Assemble Electrical Plate (D) as shown using separate fitting instruction.
8. Fully tighten all fasteners.
9. Refit crash beam to vehicle rear panel, over towbar Cross Tube (A) and refit towing eye bush.
10. Cut bumper as shown and refit to vehicle.
For use with either
VL46A Flange neck option – ZF3013. Note: This towbar must be used with either a Witter Towball (part number Z11) or
Class A50-1 or A50-X towball, which dimensionally conforms to A50-1 with a 'D' and 'S' value greater than or equal to that of the
towbar.
VL46AQ Detachable neck option – ZQ3013. Please refer to ZQ fitting instructions for installation
Recommended torque settings: M8 - 27Nm, M10 - 53 Nm, M12 - 95 Nm, M14 - 150 Nm, M16 - 214 Nm
Grade 10.9: M12 – 139Nm, M10 – 78Nm
W0001VL46AU-FIT$011104070000>Ä
W0001VL46AU-FIT$011104070000
TOWBAR
VL46AU
Volvo XC70
For
October 2007-
VL46A
VL46AQ
E
EP
XC 70
BU M PER
C L

Publicité

loading

Sommaire des Matières pour Witter VL46AU

  • Page 1 For use with either VL46A Flange neck option – ZF3013. Note: This towbar must be used with either a Witter Towball (part number Z11) or Class A50-1 or A50-X towball, which dimensionally conforms to A50-1 with a ‘D’ and 'S' value greater than or equal to that of the towbar.
  • Page 2 10. Découper le pare-chocs et le réinstaller (voir illustration). Remarque : Cet attelage doit être utilisé avec une boule de remorquage Witter (référence produit Z11) ou une boule de remorquage Classe A50-1 ou A50-X se conformant dimensionnellement Conforme à...