Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Installation
5
5.2.2 Évacuation à l'extérieur par
l'arrière (conduit horizontal de
type B)
3/8" TO EDGE
12"
NOTE: IT IS VERY IMPORTANT
TO
READ AND FOLLOW
THE DIRECTIONS
INSTRUCTION S
IN THE INSTALLATION
BEFORE PROCEEDING
WITH THIS
REAR WALL TEMPLATE.
serves to position the bottom
4"
This Rear Wall Template
mounting plate and to locate
the horizontal exhaust
outlet.
the template is positioned
1. Use a level to check that
2. Locate and mark at least
accurately.
one stud on the left or
right side of the centerline.
It is important to use at
least one wood
a stud to support the weight
screw mounted firmly in
two additional, evenly spaced
of the microwave. Mark
locations for the supplied
toggle bolts.
3. Drill holes in the marked
locations. Where there is
for wood screws. For holes
a stud, drill a 3/16" hole
stud, drill 5/8" holes for
that do not line up with a
toggle bolts.
MOUNTING PLATE
DO NOT INSTALL THE
AT THIS TIME.
from the rear wall.
4. Remove the template
book for your
5. Revie
w
h t
e Installation Instruction
installation situation.
para consultar la
Darle vuelta a la hoja
versión en Español.
to align with holes in the
Locate and mark holes
mounting plate.
IMPORTANT:
STUD ON EITHER SIDE
OF
LOCATE AT LEAST ONE
THE CENTERLINE.
FOR 2 ADDITIONAL,
EVENLY
MARK THE LOCATION
IN THE MOUNTING PLATE
SPACED TOGGLE BOLTS
AREA.
along the dotted line.
Trim the rear wall template
Vue d'ensemble de l'installation
B1. Préparation du mur arrière
B2. Retrait de la plaque du ventilateur
B3. Fixation de la plaque de montage au mur
B4. Préparation de l' a rmoire supérieure
B5. Ajustement du ventilateur
B6. Installation du four à micro-ondes
Assurez-vous que les vis du moteur
du ventilateur et de la plaque du
A
ventilateur sont correctement ser-
rées lorsque vous les remettez en
place. Cela permet d' é viter des vibra-
tions excessives.
Assurez-vous que le câblage du mo-
A
teur a été effectué et correctement
fixé, et que les câbles ne sont pas
coincés.
54 / 63 FR
along the dotted line.
Trim the rear wall template
to align with holes in the
Locate and mark holes
t n
n i
g
l p
t a
. e
m
o
u
IMPORTANT:
STUD ON EITHER SIDE
OF
LOCATE AT LEAST ONE
THE CENTERLINE.
FOR 2 ADDITIONAL,
EVENLY
MARK THE LOCATION
IN THE MOUNTING PLATE
SPACED TOGGLE BOLTS
AREA.
Four à micro-ondes à convection à hotte intégrée / Manuel d'installation
B1. Préparation du mur arrière pour
l'évacuation à l'extérieur par l'arrière
Vous devez percer une ouverture dans le mur ar-
rière pour l' é vacuation à l' e xtérieur.
NOT E:
REA D
IT IS VER
AND FOLL
Y IMPO
IN THE
OW THE
RTAN
T TO
BEFO
INST AL
DIRE CTIO
RE PRO
L
A
T
I
O
N
REA R
CEE DING
I
N
S
TRU CTIO
NS
WAL L
TEM PLAT
WITH
NS
This Rear
THIS
mount ing
Wall Templ
E.
3/8" TO EDGE
outlet.
plate and
ate serves
12"
to locate
the horizon
to positio
n the bottom
1. Use
a level
tal exhaus
accura
to check
that the
t
2. Locate
tely.
templa
right side
and mark
te is positio
of the center
at least
one stud
ned
4"
It is import
line.
on the
screw mount
ant to use
left or
of the microw
ed firmly
at least
locatio ns
ave. Mark
in a stud
to suppor
one wood
for the
two additio
t the weight
3. Drill
holes in
supplie
d toggle
nal, evenly
a stud,
the marke
bolts.
spaced
that do
drill a 3/16"
d locatio
ns. Where
toggle
not line
up with
hole for
wood screws
there is
bolts.
a stud,
. For holes
DO NOT
drill 5/8"
holes for
AT THIS
INSTA LL
4. Remov
TIME.
THE MOUN
5. Review
e the templa
TING PLATE
the Installa
te from
installa
tion situatio
tion Instruc
the rear
wall.
n.
tion book
for your
Darle vuelta
versió n
a la hoja
en Españ
para consu
ol.
ltar la
Loca te
and mark
moun ting
holes to
IMPO RTAN
plate .
align with
holes in
LOC ATE
T:
the
AT LEAS
THE CEN
T ONE
TERL INE.
STUD
MAR K
ON EITH
THE LOC
ER SIDE
SPAC
ED TOG
ATIO N
OF
GLE BOLT
FOR 2
ADD ITION
ARE A.
S IN THE
AL, EVEN
MOU NTIN
LY
G PLAT
E
Trim the
rear wall
temp late
alon g
the dotte
d line.
Loca te
and mark
moun ting
IMPO RTAN
LOC ATE
THE CEN
MAR K
THE LOC
SPA CED
ARE A.
• Lisez les instructions relatives au GABARIT
POUR MUR ARRIÈRE.
• Collez-le au mur arrière avec du ruban adhésif,
en l' a lignant sur les trous préalablement percés
pour les trous A et B de la plaque de montage.
• Percez l'ouverture conformément aux
instructions sur le GABARIT POUR MUR ARRIÈRE.
Trim the
rear wall
temp late
alon g
the dotte
d line.
holes to
plate .
align with
holes in
T:
the
AT LEAS
T ONE
TERL INE.
STUD
ON EITH
ATIO N
ER SIDE
TOG GLE
FOR 2
OF
ADD ITION
BOLT S
IN THE
AL, EVEN
MOU NTIN
LY
G PLAT
E
Publicité
Chapitres
Table des Matières
