General View (Fig. 1); Description Of The Machine; Technical Data - Proxxon KG 50 Manuel D'utilisation

- Keep handles dry, clean, and free of oil and grease.
15. Pull the plug from the electric socket
- when the power tool is not being used, before maintenance,
and when replacing tool parts such as the saw blade, drill,
or milling cutter.
16. Never leave any tools keys or chucks plugged in
- Before switching on, check to see if the key, chuck, and
adjusting tools have been removed.
17. Prevent unintended starts
- Ensure the switch is switched to the off position when plug-
ging the plug into the electrical outlet.
18. Use an extension cable for outdoor areas
- Use only approved and accordingly marked extension
cables when working outdoors.
19. Be alert
- Pay attention to what you are doing. Tackle the work with a
reasonable attitude. Do not use the power tool if you lack
concentration.
20. Check the power tool for any possible damage
- Before continued use of the power tool, protective equip-
ment and slightly damaged parts must be carefully checked
for their flawless functioning and that they function as
intended.
- Check to see if movable parts are working perfectly and do
not jam and if there are any damaged parts. All parts must
be correctly installed and all conditions fulfilled to ensure
the flawless operation of the power tool.
- Damaged protective equipment and parts must be repaired
or replaced by an authorized specialist workshop as direc-
ted unless otherwise specified in the operating instructions
- Damaged switches must be replaced by a customer service-
center.
- Do not use any power tools in which the switch cannot be
switched on and off.
21. CAUTION!
- The use of other tools and accessories can result in the risk
of injury.
22. Have your power tool repaired by a trained and skilled elec-
trician
- This power tools complies with the relevant safety regula-
tions. Repairs may only be carried out by skilled and trained
electricians with use of genuine spare parts. Otherwise,
accidents could result for the user.

2. General view (fig. 1)

1. Cutting head
2. Cutting disk cover
3. Blocking lever
4. Cutting disk
5. Device foot
6. Setscrew
7. Rotary plate
8. Stop screw
9. Spindle for clamping device
10. Limit stop
11. Clamping device
12. Scale
13. Fixing bore

3. Description of the machine

Thank you very much for acquiring a PROXXON KG 50 capping
device:
It is perfectly suited for small but precise applications when
cutting metal bars of up to diameters of ca. 10 mm, for cutting
wood, and plastic bars or profiles.
The device consists of a cutting head and a device foot made
from die-cast aluminum. The cutting head houses the device's
electrical components as well as the synchronous belt-drive for
actuating the cutting blade. It can be swiveled up and down
through the use of a joint on the device foot and is held by a
spring in the upper setting in the neutral position.
The device foot contains a circular table that can be rotated 45°:
This allows simple and precise fabrication even of diagonal cuts.
On top of that, the scale on the side permits an exact and comfor-
table angular adjustment: after that, the circular table can be lok-
ked in place using a thumbscrew.
You can clamp the workpiece into the desired position using the
vice. The vice has a span of max. 20 mm and can hold size HO
model-railroad tracks by using a prism on the top (see fig. 6).
Fixating round materials is also made easy through the use of the
groove worked into the jaw.
Even cutting workpieces to length is perfectly possible with this
device through use of the limit stop: this can be set to a maxi-
mum length of 140 mm.
5-each ceramic-bonded cutting disks and a hollow hexagon
wrench are included with the device.

3.1. Technical data

Dimensions and weights:
Device foot:
Height:
(when the cutting head is in the rest position)
Width:
Vice
jaw width:
Span:
Weight:
Motor:
Voltage:
Power consumption:
Speed:
Cutting speed:
Noise emission:
For use in dry environments only
Protection class II device
Please do not dispose in domestic waste!
ca. 100/135 x 132 mm
ca. 100 mm
ca. 140 mm
30 mm
20 mm
ca. 1.4 kg
220 - 240 Volt,
50/60 Hz
85 Watt 10 min
8000/min
ca. 25 m/sec.
< 70 dB(A)
9