Unloading The Dishwasher - Atag VA7016SRT Mode D'emploi

Intensive mode
Improves the dishwashing results, but the dishwasher uses more energy
and water. The programme time is extended.
Select an option
To select an option, press the option button until the desired option is
shown on the display. The available options vary between programmes.
Auto Open
The dishwasher door opens automatically at the end of the programme,
which improves the drying results. (If the dishwasher is built-in the
surrounding furnishings must be resistant to any condensation from
the dishwasher.)
For a brief description, press and hold the button for Auto Open.
NOTE!
The dishwasher door must not be blocked when set to open
automatically. This can disrupt door lock functionality.
Delayed Start
When you select Delayed Start, the dishwasher will start 1-24 hours
after you have pressed the button Start/Stop and closed the door.
1 Press the button once to activate Delayed Start. Press the button
several times – or hold it in – to set the desired number of hours.
2 Press Start/Stop and close the door. The timer counts down and
the dishwasher starts after the selected delay.
If you want to cancel the Delayed Start option, open the door and press
and hold the main power switch until the display turns off.
START
Starting the dishwasher
STOP
Press and hold Start/Stop until the display shows "Program started,
close door". This indicates that the dishwasher is ready to start. Close
the door properly, or the dishwasher will not start.
If the dishwasher is not started or the door is not closed within 2 minutes
of the last button press, the machine switches off.
Time remaining
Once you have chosen a programme, programme mode and options,
the time the programme took when last used is displayed.
Status light
Status light
The status light at the bottom on the dishwasher provides information
by means of 3 different colours.
Blue - Load more
The programme has started, but you can still load more dishes.
Red - Do not load
You should not load more dishes (risk of poorer dishwashing result).
Flashing red indicates a problem. See also the chapter Troubleshooting.
Green - Unload
The dishwashing programme is finished. Standby light for 60 minutes.
Stopping or changing a programme
If you want to change programme after starting the dishwasher, open
the door then press and hold Start/Stop for three seconds. Add more
detergent if the lid of the detergent dispenser has opened. Then choose
a new programme, press Start/Stop and close the door.
If you want to load more dishes
Open the door. The dishwasher stops automatically. Add the dishes
and close the door. After a while, the dishwasher continues the
programme.
If the dishwasher is turned off due to a
power failure
If the dishwashing programme was not finished, the interrupted
programme continues when power is restored.
NOTE!
During drying, the programme is interrupted if the power is cut or
the door is open for more than 2 minutes.
Once the programme has finished
Once the programme has finished and the door is opened "Ready"
appears on the display.
At the end of the programme one short signal will sound. Chapter
Settings describes how to change this function.
Moreover, the end of the programme is indicated by the status light
turning green.
The dishwasher switches off automatically after the programme ends.
Shut off the water tap after each use.
How to get the best drying results
Fully load the dishwasher.
Angle dishes with hollows, such as cups, so that the rinse water
will run off. This is also important for plastic items.
Top up with rinse aid or increase the rinse aid dosage level.
Activate the Auto Open option.
Activate the High temperature setting. See the chapter Settings.
Allow the dishes to cool before unloading the dishwasher.

Unloading the dishwasher

Hot porcelain is more fragile. Leave the dishes to cool in the dishwasher
before unloading them.
Unload the lower basket first to avoid any water drops from the upper
basket falling onto the dishes in the lower basket.
11