Electrical Grounding; Cut-Out Dimensions - NewAge Products 65900 Manuel D'installation Et Fonctionnement

Installing Briquettes, Grill Grates and Rotisserie cont.
Drop the notched endcap of the skewer
onto the rollers(B) . The notched slot on the
7
skewer needs to align with rollers mounted
on grill housing. Figure (C).
B
C
Note: In order for the rotisserie, LED and halogen
lights to work the grill must be plugged into a GFCI
outlet installed by an electrician.
GFCI
electric plug for your protection against shock hazard and must be plugged directly into a properly grounded
three prong outlet. Never cut or remove the grounding prong from this plug.
• Use only extension cords with a 3 prong grounding plug, rated for the power of the equipment, and
approved for outdoor use with a "W-A" MARKING.
• To protect against electric shock, do not immerse any part of the power cord, an extension cord or any
plugs in water or other liquid.
• Unplug the product from the outlet when not in use and before cleaning. Allow it to cool before putting
on or taking off parts.
• Do not let the cord hang over the edge of a table or touch hot surfaces.
• Do not use an outdoor cooking gas appliance for purposes other than intended.
• Do not operate any outdoor cooking gas appliance with a damaged cord, plug, or after the appliance
malfunctions or has been damaged in any manner. Contact the manufacturer for repair.
16
www.newageproducts.com
8
5
WARNING!

ELECTRICAL GROUNDING

•
Product installation must
meet local electric codes or,
!
in the absence of local codes,
the latest edition of the
National Electrical Code ANS/
NFPA No. 70 or the
Canadian Electrical Code CGA
1.6b2005.
• Use only a Ground Fault Interrupter (GFI) protected
circuit with this outdoor cooking gas appliance.
• IMPORTANT: When connecting your rotisserie motor,
first connect the motor to the grill and then plug the
grill into the outlet.
• This grill is equipped with a three prong (grounding)
Cutout Dimensions for Built-in
The installation must conform with local codes or, in the absence of local
codes, with the National Fuel Gas Code, ANS Z223.1/NFPA 54, Storage
and Handling of Liquefied Petroleum Gases, ANS/NFPA 58; or Natural Gas
and Propane Installation Code, CSA B149.1; Propane Storage and Handling.
If you are connecting an appliance to a fixed fuel piping system specifying
the use of a rigid pipe, semi-rigid tubing, and/ or a connector that complies
with the standard for Connectors for Outdoor Gas Appliances and
Manufactured Homes, ANS Z21.75 CSA 6.27
.
W H
65901 - 40" Grill 38.5" (978mm) 11.125" (283mm) 22.5" (572mm)
65900 - 33" Grill 31.5" (800mm) 22.5" (572mm)
11.125" (283mm)
OUTDOOR GFI ELECTRICAL OULET
RECOMMENDED - LOCATE ON SAME SIDE
OF GRILL AS ROTISSERIE BRACKET.
INSULATION JACKET
MAY BE REQUIRED
ELECTRICAL OPENING
GAS INLET OPENING
H
D
MINIMUM 20 SQ IN (130 SQ
CM) OF VENTILATION
REQUIRED ON EACH END OF
CABINET.
5"
5"
127mm
127mm
MAXIMUM
MAXIMUM
MINIMUM 10 SQ IN (65 SQ CM)
OF VENTILATION REQUIRED ON
EACH END OF CABINET.
25.4mm
MAXIMUM
Allow access in order to
connect or disconnect
propane hose regulator to
propane tank.
Secure 20 lbs propane tank to
interior of built in cabinet.
www.newageproducts.com
!
!
WARNING
WARNING
A propane tank can not
Cabinet frame, cabinet side panels and
counter top must be made from be stored below the gas grill.
Only 1 max 20 lbs tank in service
D non-combustionable material.
should be used with the grill.
Note to Installer:
A built-in appliance for use with
a remote LP gas supply system
where the installer constructs the
propane cylinder enclosure. The
installer must provide detailed
instructions and diagrams that
comply with clauses 4.6.1-4.6.5
2"
of the ANS Z223.1 Code.
51mm
36"
All built-in appliances must use
4"
915mm
102mm rigid pipe, semi-rigid tubing, or a
RECOMMENDED
connector complying with the
standard for Connectors for Gas
Appliances, ANS Z21.24. CSA 6.10,
or Standard for Connectors for
W Outdoor Gas Appliances and
Manufactured homes, ANS Z21.75.
CSA 6.27, for the appliance which
are connected to fixed fuel piping
system (Natural Gas).
The appliance, when installed, must be
electrically grounded in accordance with
!
local codes or, in the absence of local
codes, with the National Electrical Code,
1" ANS/NFPA 70, or the Canadian Electrical
WARNING
Code, CSA C22.1.
17