Table des Matières
Publicité
ssembly
Included with the delivery
Check the contents of the shipping box when unpacking for,
• Completeness • possible transport damage
Communicate damage claims or missing items immediately to
your dealer, freight forwarder, or manufacturer. Later claims will
not be recognized.
• Lawn mower
• Handle – lower piece, handle – upper piece, 2 middle pieces
• Bag with mounting parts
• Operating instructions / list of repair shops
Operation
djusting the cutting height (Fig. B1)
There are 5 positions for cutting height (18, 23, 28, 32,
40 mm).
Pull the adjusting arm (1) away from the sidepiece and let it
re-engage in the desired cutting height position (2). djust, by
1 position only, alternating right and left. The adjustment arms
must always be on the same height position.Note: djust the
cutting height so that the bottom blade has no ground contact
if there are uneven areas on the lawn surface.
Mowing
To maintain a well-groomed lawn, the grass must be cut at
least once a week. The grass must be dry, for the most part,
when it is mowed. The mowing path should be as straight as
possible using a normal walking speed. The mowing paths
must always overlap by several centimetres to prevent strips
of grass being left uncut.
New blade condition „Mach 15"
Mowing:
Higher pushing forces are possible due to the design of the
system. The blade is automatically optimized, i.e. the blade
spindle adapts exactly to the bottom blade after mowing for
some time (approx. 2 hrs.).
Maintenance
Care and storage
Clean the mower after each use with a hand brush and store
in a dry location. The ball bearing, roller axle and the cutting
edges of the blades should be treated with environmentally
safe, biodegradable spray oil once a year.
Changing blades (Fig. W1)
Caution: Wear protective gloves.
Change worn blades only as a set (15 blades)
15 replacement blades TC-M, part no.: 3628 094
Guarantee terms
Please carefully retain the guarantee card completed by the
seller, or the proof of purchase.
The company WOLF-Garten provides a guarantee for 24 months
from the date of purchase. This guarantee is in accordance with
the relevant state of technology and the utilisation purpose / area of
application. The consumer's statutory rights are not affected by the
following guarantee guidelines.
Pre-conditions for the 24-month guarantee entitlement:
- Deployment of the device solely for private use.
The guarantee is reduced to 12 months in the commercial
sector or leasing business.
- Proper handling and observance of all information given in the
operating manual, which forms part of our guarantee terms.
- Observance of the prescribed maintenance intervals.
- No unauthorised alteration of the design.
8
Mount handle assembly (Fig. M1)
Handle – lower piece (1)
Handle - middle pieces (2)
Handle – upper piece (3)
djusting the lower blade (Fig. B2)
You must readjust the blade if the mower no longer cuts the
lawn uniformly and cleanly.
Caution: Wear protective gloves.
Turn over the mower as illustrated.
tightening the two lock nuts (3) on the bottom blade (4).
Required tools: Spanner (wrench) 10 mm F.
Turn the lock nut (3) to the left:
The clearance to the blade cylinder (5) decreases.
Turn the lock nut (3) to the right:
The clearance to the blade cylinder (5) increases. djust the
lower blade in such a manner that all cutting edges of the
blade cylinder touch lightly.
Cutting test with paper (Fig. B3)
Caution: Wear protective gloves.
The adjustment is correct if a piece of paper between the
blade spindle and the lower blade is cut cleanly. To do
this turn the blade cylinder by hand.
Note:
If problem-free cutting results are not obtained, in spite of
adjustment as prescribed, then the blade spindle, and/or the
bottom blade must be checked (see maintenance).
New blade condition „Mach 15"
1. djust bottom blade (B2).
2. Conduct cutting test with paper (B3).
Repairs
ll other repairs must be performed by a WOLF service
center
We recommend: Have your mower thoroughly checked once
a year by approved Service gent.
- Installation of original WOLF replacement parts / accessories.
- Presentation of the completed guarantee card and/or proof of purchase.
This guarantee does not extend to normal wear-and-tear on blades,
blade mounting components or friction disks, V-belts/toothed
belts, running wheels/tyres, air filters, spark plugs and spark plug
connectors. ny guarantee claim shall be immediately void in the
event of unauthorised repairs. Faults and defects which can be traced
to material or manufacturing faults will be rectified exclusively by our
contracted workshops (the seller has the right to remedy a defect) in
your vicinity, or by the manufacturer if the latter is closer. ny claims
going beyond the provision of a guarantee are ruled out. There is
no entitlement to a replacement.
reported not to us but to the shipper in question since, otherwise, any
compensation claims vis-à-vis the shipper would be voided.
djust by loosening or
ny transport damage should be
Publicité
Table des Matières
