Wall Mounting; Intended Use; Assembly And Adjustments - Craftsman CMCCSP 20 Guide D'utilisation

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

household
English
2. The charger and battery pack may become warm to the
touch while charging. This is a normal condition, and
does not indicate a problem. To facilitate the cooling of
the battery pack after use, avoid placing the charger or
battery pack in a warm environment such as in a metal
shed or an uninsulated trailer.
3. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out
the lights;
c. Move the charger and battery pack to a location
where the surrounding air temperature is
approximately 65 °F – 75 °F (18 °C – 24 °C);
d. If charging problems persist, take the tool, battery
pack and charger to your local service center.
4. The battery pack should be recharged when it fails to
produce sufficient power on jobs which were easily
done previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may
also charge a partially used pack whenever you desire
with no adverse effect on the battery pack.
5. Foreign materials of a conductive nature such as, but
not limited to, grinding dust, metal chips, steel wool,
aluminum foil, or any buildup of metallic particles
should be kept away from charger cavities. Always
unplug the charger from the power supply when there
is no battery pack in the cavity. Unplug the charger
before attempting to clean.
6. Do not freeze or immerse the charger in water or any
other liquid.
Charger Cleaning Instructions

WARNING: Shock hazard. Disconnect the charger
from the AC outlet before cleaning. Dirt and grease
may be removed from the exterior of the charger
using a cloth or soft non-metallic brush. Do not use
water or any cleaning solutions.

Wall Mounting

These chargers are designed to be wall mountable or to sit
upright on a table or work surface.  If wall mounting, locate
the charger within reach of an electrical outlet, and away
from a corner or other obstructions which may impede
air flow. Use the back of the charger as a template for
the location of the mounting screws on the wall. Mount
the charger securely using drywall screws (purchased
separately) at least 1" (25.4  mm) long, with a screw head
diameter of 0.28–0.35" (7–9 mm), screwed into wood to an
optimal depth leaving approximately 7/32" (5.5 mm) of the
screw exposed. Align the slots on the back of the charger
with the exposed screws and fully engage them in the slots.
Versatrack™
CRAFTSMAN chargers can be mounted to the wall using
CRAFTSMAN Versatrack™ Trackwall. Hooks and accessories
are sold separately. Please refer to the Versatrack™
Trackwall accessory sheet for further information.
8
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
COMPONENTS (FIG. A)

Intended Use

This pole saw is designed for household use.
DO nOT use under wet conditions or in presence of
flammable liquids or gases.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.

ASSEMBLY AND ADJUSTMENTS


WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
Installing and Removing Saw Chain
(Fig. A–D)

WARNING: Sharp moving blade. To prevent
accidental operation, insure that battery is
disconnected from the handle before performing the
following operations. Failure to do this could result in
serious personal injury.

CAUTION: Sharp moving blade. Always wear
protective gloves when installing or removing the
chain. The chain is sharp and can cut you when it is
not running.
1. Place the pole saw on a firm surface. Rotate the two
hex head screws 
counterclockwise with the hex
12
wrench  
provided.
16
2. Remove sprocket cover 
11
head screws.
3. To remove the saw chain 
the front of the housing using the flat screwdriver end of
the wrench. Turning the screw counterclockwise allows
the guide bar 
to recede and reduces the tension on
13
the chain so that it may be removed.
4. Lift the worn saw chain out of the groove in the
guide bar.
5. Flip guide bar over.
6. To replace the saw chain, check to make sure that the
slot in the guide bar is over the location pins
in Figure D and that hole below the slot is located over
the adjustment pin.
7. Place new chain in groove of guide bar and around
sprocket. Make sure saw teeth are facing correct
direction by matching the graphic on housing or
guide bar.
8. Rotate the screw in the front of the housing clockwise to
increase the chain tension.
9. Replace sprocket cover, bar clamp, and hex head screws.
10. Follow the instructions in the section Adjusting
Chain Tension.
, bar clamp 
10
, and hex
14
, rotate the screw 
19
in
shown
20

Publicité

Table des Matières
loading

Table des Matières