Warnings; Results Of The Tests Made According To The Laws; General Warnings - CAMPAGNOLA Stark Manuel D'utilisation Et D'entretien

Warnings

The Manufacturer declines all responsibilities if the precautions below are not taken.
The accomplishments concerning working environment safety and health regulations indicated by the current
laws (Dir. 2003/10/EC, Dir. 2002/44/EC and Legislative Decree no. 81/2008) have to be carried out either by the
end-user or by the employer: supplying the adequate personal protective equipment, informing about working
risks, health surveillance, etc....
The over-exposure to the vibrations may cause neurovascular lesions to people suffering from circulatory dis-
orders. In case of symptoms which could be referred to over-exposure, contact a specialist. These symptoms
can be torpor, loss of sensitivity, sharp pains, itching, strength reduction or loss, complexion discoloration or
structural modifications of its surface. This usually happens to one's hands, wrists and fingers.
2.1.1

Results of the tests made according to the Laws

ELECTROMAGNETIC COMPATIBILITY LEVEL
The equipment complies with the electromagnetic compatibility directive EMC 2014/30/UE

General warnings

Do not use the tool indoor or in case of potentially explosive environment.
• The product is for a non-intensive use only (for plantings with a maximum area of 3/4 hectares).
• Use the tool only with the accessories indicated by the Manufacturer.
• Use the tool only from the ground, working in a stable and safe position.
• Always use adequate clothing as called for by the job. Wear protective goggles and verify that your clothes are fitting
to the body. Do not wear ties, necklaces or belts or keep loose long hair which may get caught in the moving parts.
Use anti-sliding shoes and antiperforation gloves.
• Wear a noise-abatement headset.
• Do not operate, service or repair the tool if you are under the influence of medicines, alcohol or drugs which could
impair your alertness or co-ordination.
• Only well trained and qualified personnel - who have read the use and maintenance manual carefully - are allowed
to use the tool. The safety course must be administered by the employer.
• Entrust or lend the tool only to people who are familiar with the instructions for use or trained by personnel authorized
by the employer.
• Keep the tool out of the reach of children, as well as of people with disabilities or untrained in its use and keep it
away from animals.
• The operator is the only responsible for injuries caused to other people or for damages caused to their belongings.
• Do not use the tool when you are in an unstable position or off balance, on slipping surfaces (i.e. hills or wet grass)
or wherever there is no possibility of maintaining a stable balance (i.e. steep slopes).
• Never use the tool while standing on a ladder.
• Never cut branches which are close to electric wires.
• Before any routine maintenance operations, read the Use and Maintenance Manual carefully. For any maintenance
operation which is not indicated in this manual, please contact one of the Service Points authorized by the Manufac-
turer.
• Use the tool just for the purposes described in par. "Product description". Any other use may cause injuries.
• Remove the battery (11) before any maintenance operation.
• Keep this manual with care and read it before any tool use.
• Keep in perfect conditions all the danger and safety indications stickers.
• Do not use petrol, solvents or other aggressive products to clean the tool.
• Avoid working in bad weather conditions, such as in case of fog, rain, strong wind, hail storm, snow or ice..
• Do not cut branches in bundles. Cut one branch at a time.
• Be careful when cutting taut branches. They could cause a loss of tool control.
• Before operating the shear, check that the blade tightening adjusting tools have been removed. Any tool left on the
rotating parts of the shear could cause injuries.
• When operating the shear, keep your hands away from the cutting area. Never put your hands under the branches
for any reason. When cutting branches, check that there is nothing around which could get damaged.
• Inhaling oil mist or wood dust could cause irritation or intoxication of the operator's breathing system. In case of
prolonged problems, please contact a specialized doctor.
Pag. 22
Use and maintenance manual – Translation of
original Instruction.: 04, Date 22/11/2021