Technical Data - S+S Regeltechnik KINASGARD RBWF/LF Notice D'instruction

G
®
KINASGARD RBWF ⁄ LF
The room motion and light sensor and presence detector KINASGARD
is a combined instrument that detects motion and light intensity using a diffuser as
well as the presence of persons and is used to recognize conditions. RBWF-LF
issues a standard signal of 0 - 10 V or 4...20 mA for light intensity and has a switching
(normally open contact) output for detecting motion.
The room light intensity sensor PHOTASGARD
uring ranges (four devices in one) measures the luminous intensity with a diffuser.
Its greatest sensitivity is in the range of 400 nm to 700 nm.
The multisensors are used in building automation, in corridors, at workplaces, in
industrial halls, in offices and business facilities for the control of lighting as needed,
e.g. to control sunshade equipment, for daylight-dependant constant light control,
for activating Venetian blinds or luminaries, for automatic energy conservation, and
to avoid unnecessary heating-up or cooling of unoccupied rooms.

TECHNICAL DATA

Power supply: 24 V AC (± 20 %); 15...36 V DC for U variant
15...36 V DC for I variant, depending on working
resistance, residual ripple stabilised ± 0.3 V
Working resistance: R
a
Load resistance: R
L
Power consumption: < 1 W at 24 V DC; < 2 VA at 24 V AC
Sensor: infra-red motion sensor and light sensor with diffuser
Output, motion sensor: without ⁄ with motion + presence, potential-free
normally open contact (24 V), 1 A ohmic load
After-running time: adjustable from 4 s to 16 min
Measuring ranges: multi-range switching (via DIP switches)
with 4 switchable measuring ranges
0...500 Lux ⁄ 1 kLux ⁄ 5 kLux ⁄ 20 kLux
(other individual ranges optional, e. g. 100 kLux)
Output, light sensor: 0 -10 V (linearised, active, 3-wire connection) or 4...20 mA
Deviation, light sensor: typically < 5 % of final value
Ambient temperature: 0...+50 °C
Electrical connection: 0.14 - 1.5 mm², via terminal screws
Housing: plastic, material ABS,
colour pure white (similar to RAL 9010)
Dimensions: 85 x 85 x 27 mm (Baldur 1)
Installation: wall mounting or on in-wall flush box, Ø 55 mm, base
with 4-hole for mounting on vertically or horizontally
installed in-wall flush boxes for cable entry from the
back, with predetermined breaking point for on-wall
cable entry from top ⁄ bottom in case of plain on-wall
installation
Protection class: III (according to EN 60 730)
Protection type: IP 20 (according to EN 60 529)
Standards: CE conformity, electromagnetic compatibility according to
EN 61 326, EMC directive 2014 ⁄ 30 ⁄ EU
Type ⁄ WG01
Detection, Measuring Range
RBWF ⁄ LF Room motion sensor and light sensor
Presence + Motion: Yes ⁄ No (relay on ⁄ off)
RBWF-LF-U
Light Intensity: 0...500 Lux ⁄ 1 kLux ⁄ 5 kLux ⁄ 20 kLux
Presence + Motion: Yes ⁄ No (relay on ⁄ off)
RBWF-LF-I
Light Intensity: 0...500 Lux ⁄ 1 kLux ⁄ 5 kLux ⁄ 20 kLux
RBWF Room motion sensor
R B W F -W Presence + Motion: Yes ⁄ No (relay on ⁄ off)
RHKF Room light intensity sensors
R H K F - I Light Intensity: 0...500 Lux ⁄ 1 kLux ⁄ 5 kLux ⁄ 20 kLux
R H K F - U Light Intensity: 0...500 Lux ⁄ 1 kLux ⁄ 5 kLux ⁄ 20 kLux
Extra charge: Other individual measuring ranges optional, e. g. 100 kLux
®
RHKF with four switchable meas-
(ohm) = (U -14 V) ⁄ 0.02 A for I variant
b
> 5 kOhm for U variant
® RBWF-LF
Schematic diagram
UB+ 24V AC/DC
Output Light
Intensity in lux
UB- GND
Presence
detector
Connecting diagram
UB+ supply voltage 24V AC/DC
1
Output light intensity 0-10V (linearised)
2
3
UB- GND
13
Normally
open contact
11
12 Breaker
Measuring ranges
selectable
0...500 Lux
0... 1 kLux (default)
0... 5 kLux
0... 20 kLux
Output
Changeover contact
0 - 10 V (linearised)
Changeover contact
4 ... 20 mA
Changeover contact
4 ... 20 mA
0 - 10 V
ON
1 2 3 4
1
2
3
offset time
13 11 12
changeover
(24 V)
DIP DIP
1 2
O N OFF
OFF O N
OFF OFF
OFF OFF
Item No.
1401-41A1-1100-000
1401-41A1-3200-000
1401-41A0-4000-000
1601-41A2-2000-000
1601-41A1-2000-000
on request
Rev. 2021 - V23
RBWF ⁄ LF
4'' 16'
RBWF ⁄ LF
DIP DIP
3 4
OFF OFF
OFF OFF
O N
OFF
OFF O N