Aux-In Mode; Bluetooth Stereo Pairing Mode Setup - PERFECTPRO WORKTUBE Manuel De L'utilisateur

Note: "Bluetooth Discoverable" is the option that force the Bluetooth of this speaker to disconnect from your mobile phone and enter
the "discoverable mode". This is the way to allow the Bluetooth pairing to another device. If no new device is paired, the Bluetooth
will automatically try to connect to the last device when it is switched off and on again.
The Auto-Power management function will be activated in Bluetooth mode. If there is no signal from Bluetooth for a period of over 15
minutes, the speaker will automatically switch to standby mode. Pressing the ON/OFF button will wake up the unit.

AUX-IN MODE

A 3.5mm stereo Aux-In socket is provided on the side behind the rubber cover, for connecting an external audio device such as MP3
player or CD player (Aux cable not included with this radio).
1. Connect an audio source to the AUX-IN socket.
2. Press the SOURCE/LOCK button to select AUX input. Display will show "AUX IN".
3. Play the external player.
4. Adjust the VOLUME of both the radio and the player for comfortable listening.
5. After use, close the rubber cover to prevent moist or dust from entering into the sockets and radio.
Notes: Never use the Aux-In socket in rainy or moist conditions to prevent moist from entering the radio. Keep the rubber cover well
closed under these conditions.
The Auto-Power management function will be activated in AUX mode. If there is no signal* from the Aux-In socket for a period of
over 15 minutes, the Worktube radio will automatically switch to standby mode. Pressing the ON/OFF button will wake up the unit.
* Also when the incoming signal from the external device is too low and cannot be detected for a period of over 15 minutes by the
Auto-Power management, the Worktube radio will switch to standby mode.
To prevent this raise the output level of the external device enough to be detected.
19

BLUETOOTH STEREO PAIRING MODE SETUP

You can connect two Worktube radios into Stereo Pairing Mode speakers. When the speakers paired into Stereo Pairing Mode, you
can double the volume and enjoy the stereo sound effects via Bluetooth streaming. After pairing into Stereo Pairing Mode, the Left
speaker will be the audio source, including DAB, FM, Bluetooth and Aux-in, for the Right speaker.
1. You must have two Worktube units available to use the Bluetooth Stereo Paring function. It is recommended to place one
of these Worktube radios on your left hand side as the left audio channel, another one on your right hand side as the right audio
channel.
2. For the Worktube on your right hand side, please press the ON/OFF button briefly to switch on the unit, then press the
SOURCE button to select Bluetooth mode. This Worktube is ready for the Bluetooth Stereo Pairing function.
3. Now, you can set the Worktube on your left hand side. Please also press and release the ON/OFF button, then press the
SOURCE button to switch this Worktube to Bluetooth mode too.
4. Press and hold the SELECT/INFO/BT ST button of the Worktube on the left hand side to start Bluetooth Stereo Pairing Mode
setup. At this time, the paring indication will be displayed on LCD of this Worktube.
5. In a few seconds, both of the Worktube radios will be trying to connect to each other. Once the pairing is successful, the LCD of
both units will display a successful connection notification.
Note: Bluetooth Stereo Pairing connection can be interfered by WiFi network, Mobile devices, or any other Bluetooth devices
which could cause pairing failure. If both speaker cannot pair into Bluetooth Stereo Pairing mode successfully, please go back to
step 4 to reactivate this function.
6. If the Bluetooth Stereo Pairing mode is successfully established, a notification on LCD of both units will be displayed. After a
few seconds, the LCD of the left hand side Worktube will return to normal, but the LCD of the right hanside Worktube will keep
displaying BT Stereo notification.
7. After step 6, there will be a left speaker icon displaying on the LCD. This left audio Worktube can be used normally for all the
functions, but it can only sound the left audio channel on this unit from its current playing source.
8. The Worktube on the right will display the Bluetooth right speaker icon and the BT Stereo mode on its LCD. This Worktube will
be the passive speaker in the Bluetooth Stereo Pairing mode, and only the volume and power functions are usable.
GB GB
20