UNITEC Climate WT3081 Manuel De L'utilisateur page 19

4. Use „" 3 and „" 4 to select a threshold bet-
ween 2 and 4 hPa for a change in trend display.
5. Press the „ENTER" button 2 and the storm trend
arrow will flash.
6. Use „" 3 and „" 4 to select a threshold
between 3 and 9 hPa for a change in storm trend
display.
7. Press the „ENTER" button 2 to complete the
programming procedure.
Note: The forecast icons change if there are significant
fluctuations in atmospheric pressure or ones that you
have defined. Depending on the surroundings and land-
scape a trend change is subject to different thresholds
in order to obtain a real reading. For a storm warning
the set pressure drop has to take place within 3 hours.
Then the relevant icon and the trend arrows appear and
flash for 3 hours.
Note: The device forecasts weather conditions for the
next 12-24 hours based on changes in atmospheric
pressure. The catchment area covers approx. 30-50 km.
The weather forecasts have an accuracy of 70%-75%.
Since weather conditions cannot be forecast with
100% accuracy, we cannot be held responsible for any
losses that are caused by incorrect weather forecasts.
INDOOR TEMPERATURE, INDOOR HUMIDITY,
SETTING ALARM VALUES
1. Press the „MENU" button 1 six times until the
indoor humidity display flashes.
2. Use „" 3 and „" 4 to set the maximum
humidity for the alarm.
3. Activate the HI indoor humidity alarm by pressing
the „  ON/OFF" button 5.
4. Press the „ENTER" button 2.
5. Use „" 3 and „" 4 to set the minimum humi-
dity for the alarm.
6. Activate the LO indoor humidity alarm by pressing
the „  ON/OFF" button 5.
7. Press the „ENTER" button 2; the maximum
value and „max mem" begin to flash.
8. Press the „ENTER" button 2 for 3 seconds to
delete the maximum value.
9. Press the „ENTER" button 2.
10. Press the „ENTER" button 2; the minimum value
and „min mem" begin to flash.
11. Press the „ENTER" button 2 for 3 seconds to
delete the minimum value.
12. Press the „ENTER" button 2 to complete the
programming procedure.
1. Press the „MENU" button 1 seven times until the
indoor temperature display flashes.
2. Use „" 3 and „" 4 to choose between °C
and °F.
3. Press the „ENTER" button 2.
313531__Funk-Wetterstation_Manual_180223.indd 19
4. Use „" 3 and „" 4 to set the maximum
temperature for the alarm.
5. Activate the HI indoor temperature alarm by pres-
sing the „  ON/OFF" button 5.
6. Press the „ENTER" button 2.
7. Use „" 3 and „" 4 to set the minimum tem-
perature for the alarm.
8. Activate the LO indoor temperature alarm by pres-
sing the „  ON/OFF" button 5.
9. Press the „ENTER" button 2; the maximum
value and „max mem" begin to flash.
10. Press the „ENTER" button 2 for 3 seconds to
delete the maximum value.
11. Press the „ENTER" button 2.
12. Press the „ENTER" button 2; the minimum value
and „min mem" begin to flash.
13. Press the „ENTER" button 2 for 3 seconds to
delete the minimum value.
14. Press the „ENTER" button 2) to complete the
programming procedure.
Note: Every time the alarm is activated by pressing
the „  ON/OFF" button 5 the bell icon  appears
on the display.
OUTDOOR TEMPERATURE, OUTDOOR
HUMIDITY, SETTING ALARM VALUES
1. Press the „MENU" button 1 eight times until the
outdoor humidity display flashes.
2. Use „" 3 and „" 4 to set the maximum
humidity for the alarm.
3. Activate the HI outdoor humidity alarm by pressing
the „  ON/OFF" button 5.
4. Press the „ENTER" button 2.
5. Use „" 3 and „" 4 to set the minimum humi-
dity for the alarm.
6. Activate the LO outdoor humidity alarm by pres-
sing the „  ON/OFF" button 5.
7. Press the „ENTER" button 2; the maximum
value and „max mem" begin to flash.
8. Press the „ENTER" button 2 for 3 seconds to
delete the maximum value.
9. Press the „ENTER" button 2.
10. Press the „ENTER" button 2; the minimum value
and „min mem" begin to flash.
11. Press the „ENTER" button 2 for 3 seconds to
delete the minimum value.
12. Press the „ENTER" button 2 to complete the
programming procedure.
1. Press the „MENU" button 1 nine times until the
outdoor temperature display flashes.
2. Use „" 3 and „" 4 to select the „TEMP"
function.
3. Press the „ENTER" button 2.
4. Use „" 3 and „" 4 to choose between °C
and °F.
19 19 English
26.02.18 09:14