Simmer; Melt + Hold; Bridge - KitchenAid KCIG704FBL Guide D'utilisation

6. After the third signal tone sounds, the Boiling Sensor function
automatically selects a lower power setting to keep the water
simmering.
7. While the water is simmering, you may add any ingredients
you like, set the timer and change the power setting.
NOTE: Changing the power setting or selecting the Pause
function during Boiling Sensor function will cancel the function.
For Correct Operation of the Boiling Sensor Function:
Use water only (at room temperature).
Do not add salt, condiments or other ingredients until the
water reaches the boiling point.
Do not change the power setting of the surface cooking area
or remove or move the pot.
Fill the pot to at least 1/3 full (minimum of 1 qt [1 L]) and do
not fill the pot to the brim. See the following chart.
Do not use a pressure cooker on the surface cooking area
with the Boiling Sensor function selected.
For Optimum Results:
Do not use a lid on the pot being used in conjunction with the
Boiling Sensor function.
Do not activate the Boiling Sensor function if the surface
cooking area is already hot ("H" visible on display).
The quality of the pot used may have a bearing on the Boiling
Sensor function performance.
Important Information:
When the Bridge function is selected, the Performance Boost
and Boiling Sensor functions cannot be used. If the Timer is
set, it will be displayed alongside the surface cooking area
display.
The cooktop features automatic functions for each surface
cooking area. The available functions are shown next to the
selection key of each surface cooking area.
Each time an automatic function is selected, an indicator light
turns on next to the function and "A" appears in the surface
cooking area display.
The cooktop features automatic management of the use of
the Boiling Sensor and Performance Boost function settings;
therefore, in some cases it may not be possible to select the
Performance Boost function when the Boiling Sensor
function is selected on other surface cooking areas.
Surface Pot Base Diameter for
Cooking Area Use of Boiling Sensor
Diameter Function
7" (18 cm ) 6¹⁄₂" to 7¹⁄₂" (17 to 19 cm
9¹⁄₂" (24 cm ) 9" to 9⁴⁄₅" (23 to 25 cm )
11" (28 cm ) 9" to 11" (24 to 28 cm )

Simmer

The Simmer function can be used on with all surface cooking
areas. Simmer can be used on more than 1 surface cooking area
at a time.
To Use:
1. Check that a surface surface cooking area has been selected.
2. Touch SIMMER. "A" will appear in the display, and the
indicator light next to Simmer will light.
The timer remains visible and can be set if desired.
6
Simmer can be turned off in 3 different ways:
1. Use the power slider to set to a heat level.
OR
2. Touch the surface cooking area OFF keypad.
OR
3. Select a different cooking function.
Do not let food sit for more than one hour before or
after cooking.
Doing so can result in food poisoning or sickness.
The Melt + Hold function can be used on with all surface cooking
areas. Melt + Hold can be used on more than 1 surface cooking
area at a time.
To Use
1. Check that a surface cooking area has been selected.
2. Touch MELT + HOLD. "A" will appear in the display, and the
indicator light next to Melt + Hold will light.
The timer remains visible and can be set if desired.
Melt + Hold can be turned off in 3 different ways:
1. Use the power slider to set to a heat level.
OR
2. Touch the surface cooking area OFF keypad.
OR
3. Select a different cooking function.
Maximum
Amount of
Water in Pot
5 qts (4.7 L)
The Bridge function can be activated when surface cooking areas
are on or when they are off. The Bridge function allows you to use
7 qts (6.6 L)
2 surface cooking areas as an extra-large surface cooking area.
7 qts (6.6 L)
To Use:
1. Touch the Bridge keypad.
The indicator light above the Bridge keypad will light. The
heat setting levels for the 2 surface cooking areas will default
to "0" and can be set from a minimum of "1" to a maximum of
"9." Any timers that may be running for the 2 surface cooking
areas will turn off, and 2 dashes "--" will appear in the Timer
display.
2. Slide the Heat Level slider to change the power level up or
down.
The selected heat level will show in the Heat Level display for
each surface cooking area in the Bridge function.

Melt + Hold

WARNING
Food Poisoning Hazard

Bridge

A
A. Left side bridge