Feed Screw Loading; Setting Operating Temperature And Power - Ravelli CLASSIC 7 Manuel D'utilisation

CONNECT AN EXTERNAL THERMOSTAT WITH A SIMPLE DRY CONTACT, THEREFORE, NOT POWERED. MORE-
OVER, WE RECOMMEND YOU USE A THERMOSTAT WITH A MINIMUM OFFSET OF 3°C IF YOU INTEND TO USE
Rev.A 19.03.19
THE COMFORT CLIMA FUNCTION.
Pag.66
EN
Comfort climate
The activation of this function enables the stove to reduce pellet consumption by activating the modulation phases, after the desired
Time and date setting
temperature has been reached. Subsequently, the stove checks that the temperature is maintained steady for a preset time. If this
Loading the auger
Below are given the steps for accessing the relative menu.
condition is met, it automatically switches off, and on display appears the writing ECO.

Feed screw loading

Carry out this operation to facilitate stove's first start operations; You should also check that you have introduced pellets
The stove turns on again when the temperature drops below the set threshold.
into the hopper and wait until the stove is in "SHUTDOWN" or "FINAL CLEANING" mode. The number expressed in sec-
Before starting the stove for the first time, whenever the stove is in alarm "06 - Pellets finished", and in any case whenever the hopper
onds indicates the rotation time of the infeed screw during the first loading cycle. Once this time has elapsed, the infeed
has emptied completely, the initial feed screw loading is required. This phase involves filling the pellet loading system so that when
Below are given the steps for accessing the relative menu.
screw stops immediately and then pellets are emptied from the grate before turning on the equipment.
the system is started, it is ready to load the pellets into the brazier.
In the event that the feed screw operations are not carried out, there may be stove ignition failures.
Below are given the steps for accessing the relative menu.
MANUFACTURER
ENGINEER
MANUFACTURER
Press the "menu access"
Press the key
"access menu" to
Press the key "access
button to access the
access
menu" to access
the
MENU screen.
the
MENU page
MENU page
At the end of the auger loading, the display shows 0 "and automatically switches to the USER menu page.
Press the key for several times until the Stand-by page is displayed.
Once you have accessed the Climate Comfort menu, it is possible to operate on the 3 types of settings dedicated to the function:
THE PRE-SET INITIAL LOADING TIME IS SUCH TO ALSO INCLUDE ENOUGH PELLETS FOR THE FIRST IGNITION.
AFTER THE INITIAL LOADING OPERATIONS, NO BRAZIER CLEANING WILL PRECEDE THE IGNITION PHASE.
ALWAYS EMPTY THE BRAZIER BEFORE TURNING THE STOVE ON AND ALWAYS CHECK
THAT ALL NONE OF ITS HOLES IS CLOGGED NEVER EMPTY THE RBAZIER INSIDE THE HOPPER. COMFORT CLIMA
FIRE HAZARD.
ENABLE COMFORT

Setting operating temperature and power:

RESTART DELTA
Setting operating temperature and power:
Set the two values following the indications given in the chapter "Description of thr display"
SHUTDOWN DELAY
Set the two values following the indications given in the chapter "Description of thr display"
Turning the device on
Turning the device on
Keep the key ON/OFF pressed for a few seconds to turn on the stove.
Keep the key ON/OFF pressed for a few seconds to turn on the stove.
COMFORT CLIMA
! IMPORTANT
The appearance of the message "ADJUST THE RDS SYSTEM" indicates that the initial parameter testing procedure
ENABLE COMFORT
and calibration has been unsuccessfully. This indication does not cause stove blockage (see the SIGNALLING POP UP
RESTART DELTA
section).
SHUTDOWN DELAY
On the display of the handheld set appears the following:
COMFORT CLIMA
ENABLE COMFORT
RESTART DELTA
SHUTDOWN DELAY
Press and hold the ON/OFF button to turn off the stove door, and reset any alarms triggered.
In case the infeed screw operations described avobe have not been executed, the stove may fail to turn on. In this case,
! IMPORTANT
Press the key for several times until the Stand-by page is displayed.
carry out the operations described above and empty the brazier and reset the alarm.
If the stove still fails to turn on, check that the grate is properly installed and perfectly adherent to the base, and also check that
there are no deposits that prevent the smooth passage of air to enable ignition. If the problem persists, contact the support ser-
vice.
Sequence of ignition phases
What happens if the batteries are empty?
Use and maintenance manual Classic 7-9
User's manual HANDHELD TOUCH RADIO
MENU
MENU
USER
USER
ENGINEER
Press the "confirm"
Press the key
button to access the
Press the key
"confirm"
to access the "confirm"
USER screen
USER page
to access the
USER page
The appearance of the message "ADJUST THE RDS SYSTEM" indicates that the initial parameter
testing procedure and calibration has been unsuccessfully. This indication does not cause stove
blockage (see the SIGNALLING POP UP section).
In case the infeed screw operations described avobe have not been executed, the stove may fail to
turn on. In this case, carry out the operations described above and empty the brazier and reset the
alarm.
SWITCH-ON- initial pellet loading phase;
WAIT FLAME - flame
development wait
phase;
FLAME PRESENT - flame stabilization
phase and reduction of combustible
inside the brazier;
If the battery is discharged, within the
"drop" is shown a symbol that indicates
that the battery is empty, while maintain-
ing active the features of your device.
USER
USER
SCREW FEEDING
CHRONOTHERMOSTAT
SCREW FEEDING
AIR-PELLET SET
CHRONOTHERMOSTAT
STOVE STATE
AIR-PELLET SET
STOVE STATE
ENABLE COMFORT
COMFORT CLIMA DELTA
SHUTDOWN DELAY
Vers. 01 of:07.04.14
SCREW FEEDING
COMFORT CLIMA
SETTINGS
Press the "confirm"
Press the key "selection" for
"selection"
Press CONFIRM to enable button to activate feed
to switch to the second page
the rotation of the auger
screw rotation
of USER MENU and select
CLIMATE COMFORT.
ENABLE COMFORT
COMFORT CLIMA DELTA
SHUTDOWN DELAY
WORK - operation phase
described in
the dedicated chapter;
As soon as the level of the battery
prevents the radio communication the
handheld set displays on full screen the
picture of empty battery and all device
functions are locked until the batteries
are replaced
Pag.22
USER