Installing Hdw-Xb, Hdw-Xbn, And Hdw-Xbr Models - Hatco HDW Série Manuel D'installation Et D'utilisation

INSTALLATION
Installing HDW-XB, HDW-XBN, and
HDW-XBR Models
HDW-XB, HDW-XBN, and HDW-XBR models are built-in units
that require installation into a cabinet before operation.
WARNING
ELECTRIC SHOCK HAzARD: Built-in units must be
installed by a qualified electrician. Installation must
conform to all local electrical codes. Installation by
unqualified personnel will void unit warranty and may lead
to electric shock or burn, as well as damage to unit and/or
its surroundings.
1. Cut the appropriate opening in the cabinet. Refer to the
"Built-In Cutout Dimensions" chart and illustration for
dimensions.
NOTE: Maintain a minimum clearance of 25 mm (1") between
the cutout opening and the floor.
2. Fasten a locking strip (not supplied) to the lower front
inside lip of the cabinet opening.
3. Make sure a properly grounded electrical supply of the
correct voltage and size is installed inside the cabinet
cutout. See the SPECIFICaTIONS section for details.
4. Partially insert the unit into the opening, making sure the
conduit is fed into the opening first.
5. Have a qualified electrician connect the unit wires from the
conduit to the electrical supply inside the cabinet.
6. Before installing the unit into the opening completely, apply
a bead of National Sanitation Foundation-approved sealant
between the heated drawer flange and the cabinet facing.
7. Slide the unit into the opening until the front locking studs
drop behind the locking strip. To verify installation, pull out
the bottom drawer completely and gently pull to ensure the
unit is locked in place.
Cabinet
Facing
Heated
Drawer
Flange
Built-In Installation (HDW-2B Model shown)
Locking
Strip
Locking Studs
(underneath)
Built-In Cutout Dimensions
Width
Model (A)
HDW-1B 28-3/8 ''
(720 mm)
28-3/8 ''
HDW-2B
(720 mm)
28-3/8 ''
HDW-3B
(720 mm)
19-3/4 ''
HDW-1BN
(502 mm)
19-3/4 ''
HDW-2BN
(502 mm)
19-3/4 ''
HDW-3BN
(502 mm)
28-7/16 ''
HDW-1BR
(722 mm)
28-7/16 ''
HDW-2BR
(722 mm)
28-7/16 ''
HDW-3BR
(722 mm)
28-7/16 ''
HDW-4BR
(722 mm)
Front View
A
C
Locking
Strip
1"
(25 mm)
1/8"
(3 mm)
Cutout and Locking Strip Dimensions
12
English
Depth
(B)
24 ''
(610 mm) (257 mm)
24 ''
( 514 mm)
(610 mm)
24 ''
(610 mm) (771 mm)
28-3/8 ''
( 720 mm) ( 257 mm)
28-3/8 ''
( 720 mm) ( 514 mm)
28-3/8 ''
( 720 mm) ( 771 mm)
18-1/8 ''
(460 mm) ( 257 mm)
18-1/8 ''
( 530 mm)
(460 mm)
18-1/8 ''
( 803 mm)
(460 mm)
18-1/8 ''
( 1076 mm)
(460 mm)
Side View
B
Locking
Strip
7/8"
(22 mm)
Form No. HDWM-0214
Height
(C)
10-1/8 ''
20-1/4 ''
30-3/8 ''
10-1/8 ''
20-1/4 ''
30-3/8 ''
10-1/8 ''
20-7/8 ''
31-5/8 ''
42-3/8 ''