Before Starting The Equipment - EINHELL RT-XS 28 Mode D'emploi D'origine

Anleitung_RT_XS_28_SPK1:_
Vibration emission value a = 14.495 m/s
h
K uncertainty = 1.5 m/s 2
Additional information for electric power tools
Warning!
The specified vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equipment
is used and may exceed the specified value in
exceptional circumstances.
The specified vibration value can be used to compare
the equipment with other electric power tools.
The specified vibration value can be used for initial
assessment of a harmful effect.
Keep the noise emissions and vibrations to a
minimum.
Only use appliances which are in perfect working
order.
Service and clean the appliance regularly.
Adapt your working style to suit the appliance.
Do not overload the appliance.
Have the appliance serviced whenever
necessary.
Switch the appliance off when it is not in use.
Wear protective gloves.
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain residual
risks cannot be rules out. The following hazards
may arise in connection with the equipment's
construction and layout:
1. Lung damage if no suitable protective dust mask
is used.
2. Damage to hearing if no suitable ear protection is
used.
3. Health damage caused by hand-arm vibrations if
the equipment is used over a prolonged period or
is not properly guided and maintained.

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Always pull the power plug before making
adjustments to the equipment.
02.09.2010 7:43 Uhr Seite 11
2 5.1 Installing the dust container (Figure 2/Item 5)
Slip the dust container (5) onto the vacuum
cleaner connector (a).
The dust is extracted directly through the
grinding/sanding paper and the grinding/sanding
plate and into the dust container.
5.2 Installing the dust extractor adapter
(Figure 2/Item 10)
Slip the dust extractor adapter (10) onto the vacuum
cleaner connector (a) as shown in Figure 2. Connect
the dust extractor adapter to a suitable dust
extraction system.
Important.
For health safety reasons it is imperative that you
use a dust container or a dust extraction system.
5.3 Adjusting the additional handle (Fig. 3/4)
The additional handle engages in 4 positions
(90° steps).
Pull the additional handle upwards (1). (Fig. 3)
Turn the additional handle (1) into the required
working position. (Fig. 4)
Let go of the additional handle.
Ensure that the additional handle is securely
engaged in the required position.
5.4 Fitting/removing the sanding/grinding plates
(Fig. 5/6)
Use the Allen key (11) to remove the Allen screw
(a) and the washer (b) (Fig. 5).
Then remove the sanding/grinding plate (c) (Fig.
5).
To assemble, proceed in reverse order.
When fitting the sanding/grinding plate (6 / 8)
make sure that the 4 rubber stoppers (d) are
inserted into the corresponding mounts (e). (Fig.
6)
Check that the sanding/grinding plate is secure.
5.5 Rectangular sanding/grinding plate
(Fig. 6/7/8)
Fit the rectangular sanding/grinding plate (6) to use
the equipment as an orbital sander/grinder.
5.5.1 Fasting the sanding/grinding paper with a
clamping system
Use of sanding/grinding paper with the
corresponding dimensions and perforations (Fig. 7):
Press the lever (a) upwards.
Insert the sanding/grinding paper (b) into the
open clamp and close the clamp.
Lay the sanding/paper over the oscillating plate
so that the paper is taut and clamp it again.
Make sure that the perforations in the
GB
11