Product Description And Specifications; Intended Use; Product Features; Technical Data - Bosch GSB 16 RE Professional Mode D'emploi

12 | English
is likely to bend if allowed to rotate freely without contact-
ing the workpiece, resulting in personal injury.
Apply pressure only in direct line with the bit and do
u
not apply excessive pressure.Bits can bend causing
breakage or loss of control, resulting in personal injury.
Additional safety warnings
Switch the power tool off immediately if the applica-
u
tion tool becomes blocked. Be prepared for high
torque reactions which cause kickback. The applica-
tion tool becomes blocked when it becomes jammed in
the workpiece or when the power tool becomes over-
loaded.
Hold the power tool securely. When tightening and
u
loosening screws be prepared for temporarily high torque
reactions.
Secure the workpiece. A workpiece clamped with
u
clamping devices or in a vice is held more secure than by
hand.
Use suitable detectors to determine if utility lines are
u
hidden in the work area or call the local utility com-
pany for assistance. Contact with electric lines can lead
to fire and electric shock. Damaging a gas line can lead to
explosion. Penetrating a water line causes property dam-
age or may cause an electric shock.
Always wait until the power tool has come to a com-
u
plete stop before placing it down. The application tool
can jam and cause you to lose control of the power tool.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
When working with the machine, always hold it firmly
u
with both hands and provide for a secure stance. The
machine is more securely guided with both hands.

Technical Data

Impact drill
Article number
Rated power input
Power output
No-load speed
Rated speed
Impact rate at no-load speed
Rated torque
Max. drilling diameter
– Concrete
1 609 92A 5B6 | (01.12.2020)
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.

Intended Use

The power tool is intended for impact drilling in brick, con-
crete and stone, as well as for drilling in wood, metal,
ceramic and plastic. Tools with electronic control and right/
left rotation are also suitable for screwdriving and thread
cutting.

Product Features

The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Keyless chuck
(2) "Drilling/impact drilling" selector switch
(3) Rotational direction switch
(4) Lock-on button for on/off switch
(5) On/off switch
(6) Speed preselection thumbwheel
(7) Auxiliary handle (insulated gripping surface)
a)
(8) Depth stop
a)
(9) Drill chuck key
a)
(10) Keyed chuck
a)
(11) Screwdriver bit
a)
(12) Universal bit holder
b)
(13) Hex key
(14) Handle (insulated gripping surface)
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
b) Commercially available (not included in the scope of deliv-
ery)
GSB 16 RE
3 601 A4E 5..
W
W
-1
min 0–2 800
-1
min 1 750
-1
min 47 600
Nm
mm
a)
GSB 16 RE
3 601 A4E 6..
750 750
380 380
0–2 800
1 750
47 600
2.3 2.3
16 16
Bosch Power Tools