Instellingen; Configuraciones - Paso AX6120 Manuel D'utilisation

Table des Matières

Publicité

5.

INSTELLINGEN

Op het achterpaneel bevinden zich de besturingen SETTINGS (16)
(dip-switches, leds en drukknop SET), waarmee de functieinstellingen
gecontroleerd en/of gewijzigd kunnen worden. Elke parameter wordt
onderscheiden door een adres met de betreffende waarde (ON/HIGH of
OFF/LOW). Het adres wordt geselecteerd via de dip-switches ADDRESS
(2÷8), waar 8 de meest significatieve bit is (MSB) en 2 de minst
significatieve (LSB). De waarde (of het gegeven) wordt door de dip-switch
D (1) geselecteerd.
De procedure voor het verifiëren van de ingestelde parameter is als volgt:
1) selecteer het adres via de dip-switches 'ADDRESS' (van 2 tot 8);
2) druk kort op de knop SET;
3) Als de led even knippert, is de geselecteerde parameter OFF of heeft
deze een laag prioriteitsniveau (LOW); als de led ten minste 2 sec.
lang knippert, is de geselecteerde parameter ON of met een hoog
prioriteitsniveau (HIGH).
Het aflezen hangt niet af van de stand van de dip-switch 'D' (1).
De procedure voor het wijzigen van de ingestelde parameter is als volgt:
1) selecteer het adres via de dip-switches 'ADDRESS' (van 2 tot 8);
2) selecteer via de dip-sxitch 'D' (1) de waarde van de parameter (ON =
HIGH) of (OFF = LOW);
3) druk meer dan 2 seconden op de knop SET;
4) de led knippert 2 keer om aan te geven dat de wijziging de versterker
heeft bereikt en is onmiddellijk actief (er zijn geen verdere handelingen
nodig).
In de onderstaande tabel worden alle instellingen toegelicht.
Beschrijving instelling
Descripción de configuración
Niet toegepaste instelling
Configuración no utilizada
Prioriteitsniveau Telefoon
Nivel de prioridad Teléfono
Prioriteitsniveau Microfoonposten
Nivel de prioridad Puestos
Prioriteitsniveau MIC.1
Nivel de prioridad MIC.1
Prioriteitsniveau voorrang
Nivel de prioridad Precedencia
Muting MIC.1 vanuit voorrang
Muting MIC.1 por precedencia
Muting MIC.2 vanuit voorrang
Muting MIC.2 por precedencia
Muting MIC.3 vanuit voorrang
Muting MIC.3 por precedencia
Muting MIC.4 vanuit voorrang
Muting MIC.4 por precedencia
Muting MIC.5 vanuit voorrang
Muting MIC.5 por precedencia
Muting MIC.1 vanuit VOX MIC.1
Muting MIC.1 por VOX MIC.1
Muting MIC.2 vanuit VOX MIC.1
Muting MIC.2 por VOX MIC.1
Muting MIC.3 vanuit VOX MIC.1
Muting MIC.3 por VOX MIC.1
Muting MIC.4 vanuit VOX MIC.1
Muting MIC.4 por VOX MIC.1
Muting MIC.5 vanuit VOX MIC.1
Muting MIC.5 por VOX MIC.1
D = oFF
D = oN
ADDRESS
X
X
LOW
HIGH
LOW
HIGH
LOW
HIGH
LOW
HIGH
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
T
E
E
H
S
A
T
A
D
5.

CoNFIGuRACIoNES

En el panel trasero están disponibles los mandos SETTINGS (16)
(dip-switches, LED y pulsador SET) que permiten comprobar y/o modificar
las configuraciones de funcionamiento. Cada parámetro tiene su dirección
y su valor (ON/HIGH ó OFF/LOW). La dirección se selecciona con los dip-
switches ADDRESS (2÷8), donde 8 es el bit más significativo (MSB) y 2
es el bit menos significativo (LSB). El valor (o dato) se selecciona con el
dip-switch D (1).
Las operaciones para comprobar el parámetro configurado son las siguientes:
1) seleccionar la dirección por medio de los dip-switches ADDRESS (2÷8);
2) apretar brevemente el pulsador SET;
3) si el LED parpadea brevemente, el parámetro seleccionado está OFF
o tiene nivel de prioridad bajo (LOW); si el LED parpadea durante por
lo menos 2 segundos, el parámetro seleccionado está ON o tiene nivel
de prioridad alto (HIGH).
Nota: la lectura es independiente de la posición del dip-switch 'D' (1).
Las operaciones para modificar el parámetro configurado son las siguientes:
1) seleccionar la dirección por medio de los dip-switches ADDRESS (2÷8);
2) seleccionar, mediante el dip-switch D (1), el valor del parámetro (ON
= HIGH) o (OFF = LOW);
2) apretar por más de 2 segundos el pulsador SET;
3) el LED parpadea 2 veces para indicar que la modificación ha sido
adquirida por el amplificador y está inmediatamente activa (no es
necesario efectuar otras operaciones).
En la tabla siguiente se muestran todas las configuraciones.
Beschrijving instelling
Descripción de configuración
Chime vanuit microfoonposten
Chime desde puestos
Chime vanuit voorrang
Chime por precedencia
Inschakeling VOX MIC.1
Activación VOX MIC.1
Oproep Z1 vanuit VOX TEL
Llamada Z1 desde VOX TEL
Oproep Z2 vanuit VOX TEL
Llamada Z2 desde VOX TEL
Oproep Z3 vanuit VOX TEL
Llamada Z3 desde VOX TEL
Oproep Z1 vanuit VOX MIC.1
Llamada Z1 desde VOX MIC.1
Oproep Z2 vanuit VOX MIC.1
Llamada Z2 desde VOX MIC.1
Oproep Z3 vanuit VOX MIC.1
Llamada Z3 desde VOX MIC.1
Oproep Z1 vanuit voorrang
Llamada Z1 desde precedencia
Oproep Z2 vanuit voorrang
Llamada Z2 desde precedencia
Oproep Z3 vanuit voorrang
Llamada Z3 desde precedencia
Verhoogt vrijgave VOX + 2"
Aumento desactivación VOX + 2"
Verhoogt vrijgave VOX + 4"
Aumento desactivación VOX + 4"
AX6000 SERIES
D = oFF
D = oN
ADDRESS
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
35

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Ax6240

Table des Matières