Low Battery Warning - DeWalt DCD792 Guide D'utilisation

Torque Adjustment Collar (Fig. D–F)
Your tool has an adjustable torque screwdriver mechanism
for driving and removing a wide array of fastener shapes
and sizes and in some models, a hammer mechanism for
drilling into masonry. Circling the collar
drill bit symbol, and in some models, a hammer symbol.
These numbers are used to set the clutch to deliver a torque
range. The higher the number on the collar, the higher the
torque and the larger the fastener which can be driven. To
select any of the numbers, rotate until the desired number
aligns with the arrow.
nOTE: The torque adjustment collar is only engaged during
screwdriving mode and not in drill and hammerdrill modes.
Fig. D Fig. E
3
4
Dual Range Gearing (Fig. D–F, J)

WARNING: Tool Connect™ allows for the speed of
the drill to be configured to values lower than the
rating on the tool label. If you are unsure of the current
configuration, press the selector mode button
(Fig J) to set the tool to the Home setting as described
on the label and this manual.
The dual range feature of your drill/driver allows you to shift
gears for greater versatility.
1. To select speed 1 (high-torque setting), turn the tool off
and permit it to stop. Slide the gear shifter
(towards the chuck).
2. To select speed 2 (low-torque setting), turn the tool off
and permit it to stop. Slide the gear shifter back (away
from the chuck).
nOTE: Do not change gears when the tool is running.
Always allow the drill to come to a complete stop before
changing gears. If you are having trouble changing
gears, make sure that the dual range gear shifter is either
completely pushed forward or completely pushed back.
Gear speed settings are preset at the factory but can be
customized using the Tool Connect™ app. Refer to Mode
Selector table for factory presets.
Worklight (Fig. A)

CAUTION: Do not stare into worklight. Serious eye
injury could result.
The worklight 5 located on the foot of the tool is activated
when the trigger switch is depressed. In the Home
setting, when the trigger is released, the worklight will
stay illuminated for up to 20 seconds. If the trigger switch
remains depressed, the worklight will remain on. Worklight
settings can be customized using the Tool Connect™ app.
Worklight settings can be customized using the Tool
Connect™ app. Refer to Mode Selector.
Spotlight Mode
The high setting is the spotlight mode. The spotlight will
run for 20 minutes after the trigger switch is released. Two
minutes before the spotlight will shut off, it will flash twice
and then dim. To avoid the spotlight shutting off, lightly tap
3 are numbers, a
the trigger switch.


Fig. F

3

Low Battery Warning

When in spotlight mode and the battery is nearing
4
complete discharge, the spotlight will flash twice and then
dim. After two minutes, the battery will be completely
discharged and the drill will immediately shut down. At this
point, replace with a fresh battery.

12
Keyless Single Sleeve Chuck (Fig. G–I)

4 forward

Your tool features a keyless chuck
sleeve for one-handed operation of the chuck. To insert a
drill bit or other accessory, follow these steps.
1. Turn tool off and disconnect tool from power source.
2. Grasp the black sleeve of the chuck with one hand
3. Insert the accessory about 3/4" (19 mm) into the chuck
Fig. G
WARNING: While using the worklight in medium
or spotlight mode, do not stare at the light or
place the drill in a position which may cause
anyone to stare into the light. Serious eye injury
could result.
CAUTION: When using the tool as a spotlight, be sure
it is secured on a stable surface where it will not cause
a tripping or falling hazard.
CAUTION: Remove all accessories from the chuck
before using the drill as a spotlight. Personal injury or
property damage could result.
WARNING: To reduce the risk of injury, always have a
back-up battery or secondary lighting available if the
situation warrants it.
WARNING: Do not attempt to tighten drill bits (or
any other accessory) by gripping the front part of the
chuck and turning the tool on. Damage to the chuck
and personal injury may result. Always lock off trigger
switch and disconnect tool from power source when
changing acces sories.
WARNING: Always ensure the bit is secure before
starting the tool. A loose bit may eject from tool
causing possible personal injury.
and use the other hand to secure the tool. Rotate the
sleeve counterclockwise far enough to accept the
desired accessory.
and tighten securely by rotating the chuck sleeve
clockwise with one hand while holding the tool with the
other. Your tool is equipped with an automatic spindle
lock mechanism. This allows you to open and close the
chuck with one hand.
Fig. H
6
English
with one rotating
6
Fig. I
9