Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
2. Adjust the depth adjustment lever by rotating it in the
desired direction about 1/8 of a revolution.
3. Retighten nut.
Bevel Angle Adjustment (Fig. A, I)
The bevel angle adjustment mechanism can be adjusted
between 0° and 57°.
To achieve better accuracy in cutting, use the fine adjustment
markings located on the pivot bracket
1. Raise the bevel adjustment lever
2. Tilt the shoe to the desired angle by aligning the fine
bevel pointer
22
with the desired angle mark on the
pivot bracket
21
.
3. Lower the bevel adjustment lever to retighten.
Bevel Detent (Fig. A, I)
The DCS570 is equipped with a bevel detent feature. As you
tilt the shoe
5
you will hear a click and feel the shoe stop
at both 22.5 and 45 degrees. If either of these is the desired
angle, retighten the lever
another angle, continue tilting the shoe until the coarse
bevel pointer
23
or the fine pointer
desired mark.
Cut Length Indicator (Fig. A)
The markings on the side of the shoe
the slot being cut into the material at the full depth of the
cut. The markings are in increments of 5 mm.
Kerf Indicator (Fig. K)
The front of the saw shoe has a kerf indicator
and bevel cutting. This indicator enables you to guide the
saw along cutting lines penciled on the material being
cut. The kerf indicator lines up with the left (outer) side of
the saw blade, which makes the slot or "kerf" cut by the
moving blade fall to the right of the indicator. Guide along
the penciled cutting line so that the kerf falls into the waste
or surplus material.
Mounting and Adjusting the Parallel
Fence (Fig. P)
The parallel fence
28
is used for cutting parallel to the edge
of the workpiece.
Mounting
1. Slacken the parallel fence adjustment knob
the parallel fence to pass.
2. Insert the parallel fence
3. Tighten the parallel fence adjustment knob
Adjusting
1. Slacken the fence adjustment knob
parallel fence
28
to the desired width. The adjustment
can be read on the parallel fence scale.
2. Tighten the fence adjustment knob
21
.
10
to loosen.
10
by lowering it. If you desire
22
aligns with the
5
show the length of
for vertical
9
27
28
in the shoe as shown.
27
27
and set the
27
Mounting the Dust Extraction
Port (Fig. A, R)
Your circular saw is supplied with a dust extraction port.
To Install the Dust Extraction Port
1. Fully loosen depth adjustment lever
2. Place the shoe
3. Align the left half of the dust extraction port
upper blade guard
tab into the casting notch on the tool. When installed
correctly, it will snap fully over the original depth of
cut pointer.
4. Align the right-hand piece
5. Insert screws and tighten securely.
Prior to Operation
•
Make sure the guards have been mounted correctly. The
saw blade guard must be in closed position.
•
Make sure the saw blade rotates in the direction of the
arrow on the blade.
•
Do not use excessively worn saw blades.
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
WARNING: Always observe the safety instructions and
applicable regulations.
Proper Hand Position (Fig. L)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main
handle
26
LED Worklight (Fig. A)
The LED worklight
is depressed. When the trigger is released, the worklight will
stay illuminated for up to 20 seconds.
to allow
nOTE: The worklight is for lighting the immediate work
surface and is not intended to be used as a flashlight.
Switching On and Off (Fig. E)
.
For safety reasons the trigger switch
equipped with a lock-off button
Press the lock-off button to unlock the tool.
To run the tool, press the trigger switch
trigger switch is released, the lock-off switch is automatically
activated to prevent unintended starting of the machine.
NOTICE: Do not switch the tool ON or OFF when the
saw blade touches the workpiece or other materials.
5
in the lowest position.
31
as shown. Be sure to insert the
30
with the left.
, with the other hand on the auxiliary handle
15
is activated when the trigger switch
1
.
English
4
.
29
over
12
.
2
of your tool is
2
. As soon as the
13
Publicité
Table des Matières
