Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Display of position
Autonomous and Pace Car
Position
Tower
3
2
30357
4
2
6
7
3
2
5
6
4
(only in combination with Position Tower #30357)
The position of the Autonomous Car (address 7) and of the Pace
6
7
Car (address 8) can be displayed at the Position Tower. This func-
5
tion can be activated at the Control Unit. Therefore switch off the
Control Unit and keep the "BRAKE" button
switch on the racetrack and release the "BRAKE" button again. By
pushing the button again the function may be changed:
1 LED lights = no display
2 LEDs light = display at the Position Tower
Set the function requested and confirm your choice via "START/
ENTER".
Setting of the
cars´ basic speed
1 – 10
1
3
2
1
5
7
8
4
3
The setting of the basic speed can be effected individually for one
and/or several cars. The cars which are to be adjusted have to be
5
6
positioned on the track. The setting can be carried out on 10 levels
with the 5 LEDs indicating the different levels by flashing or perma-
nent lighting.
1 LED lights = low speed
1
5 LEDs light = high speed
2
Switch on the Control Unit, place the cars to be adjusted on the
track and press "SPEED"
5
once. A certain number of LEDs will
now light, showing the speed level last used. Push the "SPEED"
button
5
as many times until you have reached the speed desired.
Confirm by pressing "ENTER/START"
the lighting of the middle LED confirms completion of the setting,
fig.
.
6
1
1
1
2
1
3
3
8
1
7
8
3
2
5
8
6
7
6
pushed, fig.
,
2
4
(only for cars operated with speed controllers)
The setting of the braking performance can be effected individually
5
for one and/or several cars. The cars which are to be adjusted have
to be positioned on the track. The setting can be carried out on 10
levels with the 5 LEDs indicating the different levels by flashing or
permanent lighting.
1
1 LED lights = low braking effect
5 LEDs light = high braking effect
2
Switch on the Control Unit, place the cars to be adjusted on the
track and press "BRAKE"
now light, showing the brake step last used. Push the "BRAKE" but-
1 – 10
2
ton
6
as many times until you have reached the braking perfor-
mance desired. Confirm by pressing "ENTER/START"
running light and the lighting of the middle LED confirms completion
of the setting, fig.
Setting fuel tank capacity
3
4
1
5
6
6
3
2
1
5
4
3
7
8
5
5
6
4
(only for cars operated with speed controllers)
3
. A short running light and
The setting of the fuel tank capacity in combination with the Pit Lane
5
(30356) is effected for all cars simultaneously. The setting can be
carried out on 10 levels with the 5 LEDs indicating the different lev-
els by flashing or permanent lighting.
1 LED lights = low fuel capacity
1
5 LEDs light = full tank
2
Switch on the Control Unit, place the cars to be adjusted on the
track and activate the fuelling function by means of the slide switch
2
, fig.
LEDs will now light, showing the fuel capacity last used. Push the
"FUEL" button
capacity desired. Confirm by pressing "ENTER/START"
running light and the lighting of the middle LED confirms completion
of the setting, fig
Extended fuelling function
You can choose between 3 modes via the sliding switch
fig.
:
3
• OFF = cars don´t consume any "petrol"
• ON = cars consume "petrol"
• REAL = maximum speed depending on fuel tank capacity / cars
consume "petrol") (only in combination with Pit Lane 30356 or Pit
Stop Lane 30346 and Pit Stop Adapter Unit 30361)
When driving in "REAL-mode" the car with a full tank is "heavier",
Setting of cars´
braking performance
1 – 10
1 – 10
2
3
4
1
5
6
6
8
3
2
6
7
6
once. A certain number of LEDs will
.
6
2
1
1 – 10
1 – 10
2
7
8
3
4
6
7
2
1
6
7
8
3
2
6
7
. Press the "FUEL" button
7
once. A certain number of
3
7
as many times until you have reached the fuel
.
6
drives slowlier and shows a lower braking effect; a car with an empty
tank is "lighter", drives faster and shows a higher braking effect. The
current fuel tank capacity and the "fuel consumption" can only be
displayed in combination with the Driver Display 30353 and Pit Stop
30356.
Refuelling of cars with Pit Lane 30356
and Driver Display 30353
Pit Lane 30356
2
1
7
7
8
9
1
8
The car´s present tank capacity can be read via the bar display with
5 green and 2 red LEDs at the Driver Display. For refuelling drive
your car into the Pit Lane across the refuelling sensor fig.
bar display now starts to flash, fig.
by keeping the lane-change button pushed. fig.
refuellings are indicated by flashing or lighting of the yellow LEDs,
fig.
(also see Driver Display).
10
Note: cars with an empty tank are disregarded for lap-counting
in combination with Position Tower 30357.
3
. A short
Setting of tank capacity at the start of the race
Pit Lane 30356
11
2
4
3
1
13
5
6
8
(only in combination with Pit Lane 30356 and Driver Display 30353)
Irrespective of the basic setting of the tank capacity it is possible
to individually set the tank capacity for one or several cars at the
race´s start for the number of laps till the first pit stop. Push "START/
1
ENTER" once
3
; the 5 LEDs at the Control Unit will light perma-
nently, fig.
, and the Driver Display´s bar display will flash, fig.
12
Clicking the lane-change button at the corresponding speed control-
ler enables you to change the fill level, fig.
8
3
. A short
2
,
Driver Display 30353
8
10
. The
7
8
, and the car can be refuelled
. The number of
9
Driver Display 30353
12
2
1
14
7
8
.
13
.
14
15
Publicité
Chapitres
Table des Matières
