Guard Rails And Supports; Safety Instructions; Electrical Connection; Contents Of Package - Carrera DIGITAL 124 Instructions De Montage Et D'utilisation

Welcome
Welcome to the Team Carrera!
These operating instructions contain important information regard-
ing the assembly and operation of your Carrera DIGITAL 124 / 132
Black Box, including the connecting rail. Please read them carefully
and keep them in a safe place afterwards.
If you have any queries, please do not hesitate to contact our dis-
tributor or visit our websites:
www.carrera-toys.com · www.carreraclub.com
Please check the contents for completeness and possible transport
damage. The packaging contains important information and should
also be retained.
We hope you will derive a lot of pleasure from your new Carrera
DIGITAL 124 / 132 Black Box.

Safety instructions

• WARNING! Not suitable for children under 36 months. Danger of
suffocation due to small parts which may be swallowed. Caution:
risk of pinching caused by function.
• Regularly check the track and cars for damage to cables, plugs
and housings! Replace defective parts.
• The car racetrack is not suitable for outdoor operation or operation
in wet locations! Keep away from liquids.
• Do not place any metal parts onto the track to avoid short-circuits.
Do not place the track in the immediate vicinity of delicate objects,
as these could be damaged by cars hurled from the track.
• Pull the plug before cleaning the racetrack! Only use a damp cloth
for cleaning, no solvents or chemicals. When it is not in use, store
the track in a dry and dust-protected location, preferably in the origi-
nal cardboard box.
• Do not operate race track at face- or eye-level – risk of injury due
to cars being catapulted off the track.

Contents of package

1x
1x
8x
1 Carrera DIGITAL 124/132 connecting section with Black Box
1 End piece right
1 End piece left
8 Track section bolts
Instructions
Please check the contents for completeness and possible transport
damage. The packaging contains important information and should
also be retained.
6
Important Information
ExCLUSIv
EvOLUTION
Carrera DIGITAL 124/132
Please note that Exclusiv/Evolution (analog system) and Carrera
DIGITAL 124/132 (digital system) involve two separate and com-
pletely independent systems. We hereby expressly indicate that
both systems must be kept separate when setting up the track, i.e.
no connecting rail from Exclusiv/Evolution may be used together
with the connecting rail and Black Box of the Carrera DIGITAL 124/132,
even if only one of the two connecting rails (Exclusiv/Evolution con-
necting rail or Carrera DIGITAL 124/132 connecting rail and Black
Box) is attached to the current supply. Furthermore, no other Car-
rera DIGITAL 124/132 components (switches, electronic lap counter,
pit stop) may be built into an Exclusiv/Evolution course, i.e. via ana-
log operation.
Non-compliance with the above information may result in damage or
destruction of the respective Carrera DIGITAL 124/132 components.
In this case no warranty may be claimed.
Assembly instructions
1
2
1x
+ +
Before assembling please insert the connecting clips
1 2 3
in the track as shown in figure
1x
base. Move the connecting clips according to figure
of the arrow until they audibly snap in. The connecting clip may also
be inserted later. The connecting clips can be removed into both
directions by simply pressing down the clamped nose (see fig.
Fastening: To fasten the track sections on a board, it is neces-
4
sary to use the track section fasteners (Item no. 85209, not con-
tained in the package).
Note:
Carpeting is not a suitable foundation on which to build the track be-
cause of static charging, formation of fluff and ready inflammability.
Carrera DIGITAL 124/132
ExCLUSIv
EvOLUTION
4
3
. Stick tracks together on a flat
1
in direction
2
).
3

Guard Rails and Supports

1 2
3 4
Guard rails: Guard rail mounts are fitted by tilting them upwards
1
onto the verge of the track.
+
Supporting raised sections: The shank of the ball pivot is
2 3
to be inserted into the square slots provided on the underside of the
track. The supports can be made higher by using the extensions.
The pedestal of the supports can be screwed to a base if required
(screws not included).
Supporting steep curves:
4
Slanting supports of the right height are provided to support steep
curves. Fix the nonadjustable supports at the beginning and end of
the curves. Insert the heads of the supports in the round slots of the
underside of the track.

Electrical connection

1
Connect the transformer plug with the Black Box
1
Note: To avoid short-circuits and electrocution, the toy may not be
connected using foreign devices, plugs, cables or other objects for-
eign to this toy. The Carrera DIGITAL 132 car racetrack only works
properly with an original Carrera DIGITAL 132 transformer.
The PC interface (PC Unit) may only be operated together with the
original Carrera PC Unit.