Bosch GSB 1300 Professional Notice Originale page 7

A)
(13) Universal bit holder
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical Data
Impact drill
Article number
Rated power input
Power output
No-load speed
Impact rate at no-load speed
Rated torque
Clockwise/anti-clockwise ro-
tation
Spindle collar diameter
Max. drilling diameter
– Masonry
– Concrete
– Steel
– Wood
Chuck capacity
Weight according to
EPTA-Procedure 01:2014
Protection class
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
Noise/vibration information
Noise emission values determined according to
EN 62841-2-1.
Typically the A-weighted noise level of the power tool are:
95 dB(A); sound power level 106 dB(A). Uncertainty K =
5 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 62841-2-1:
2
Drilling into metal: a =7.5 m/s , K=1.5 m/s
h
Impact drilling into concrete: a =10.5 m/s
h
2
Screwdriving: a <2.5 m/s , K=1.5 m/s
h
2
Thread cutting: a <2.5 m/s , K=1.5 m/s
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
Bosch Power Tools
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
GSB 1300
Implement additional safety measures to protect the oper-
3 601 AA1 0..
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
W 550
and organising workflows correctly.
W 270
-1
min 0–2 800
Assembly
-1
min 0–44 800
u
Nm 1.5
●
Auxiliary Handle (see figure A)
mm 43
u
mm 13 Turn the wing bolt (7) anti-clockwise and guide the auxiliary
handle (8) in the required position over the drill chuck onto
mm 13
the spindle collar of the power tool.
mm 10
You can swivel the auxiliary handle (8) to any of four posi-
mm 25
tions in order to achieve a safe work posture that minimises
mm 1.5–13 fatigue.
Swivel the auxiliary handle (8) to the required position. En-
kg 1.8
sure that the four grooves of the auxiliary handle are seated
on the cams of the spindle collar. Turn the wing bolt (7)
/ II
clockwise to retighten it.
u
Setting the drilling depth (see figure A)
You can use the depth stop (9) to set the required drilling
depth X.
Press the button for depth stop adjustment (6) and insert
the depth stop into the auxiliary handle (8).
The fluting on the depth stop (9) must face downwards.
Pull the depth stop far enough out that the distance between
the drill bit tip and the edge of the depth stop corresponds
to the required drilling depth X.
2
2 2
, K=1.5 m/s
Changing the Tool
2
u
2
Keyed chuck (see figure B)
Open the keyed chuck (1) by turning it until the tool can be
inserted. Insert the tool.
Insert the drill chuck key (11) into the corresponding holes
of the keyed chuck (1) and clamp the tool evenly.
Pull the plug out of the socket before carrying out any
work on the power tool.
Do not operate your power tool without the auxiliary
handle (8).
Before carrying out any work, make sure that the wing
bolt is tightened. Loss of control can cause personal in-
jury.
Wear protective gloves when changing tools. The drill
chuck may heat up significantly when it is used for long
periods.
1 609 92A 5E5 | (10.09.2019)
English | 7