Ryobi CHT1850P Manuel D'utilisation page 19

GB GB
F F D D E E
Do not operate charger if it has received a sharp
Q
blow, been dropped, or otherwise damaged in any
way; take it to a qualified serviceman.
Do not disassemble charger; take it to a qualifi
Q
ed serviceman when service or repair is required.
Incorrect reassemble may result in a risk of electric
shock or fire.
To reduce risk of electric shock, unplug the charger
Q
from outlet before attempting any maintenance or
cleaning. Turning off controls will not reduce this risk.
Disconnect charger from power supply whennot in use.
Q
Risk of electric shock. Do not touch uninsulated
Q
portion of output connector or uninsulated battery
terminal.
Save these instructions. Refer to them frequently
Q
and use them to instruct others who may use this
unit. If you loan someonethis unit, loan them these
instructions also.
WARNING
If any parts are missing, do not operate unit until
the missing parts are replaced. Failure to do so
could result in possible serious personal injury.
SAVE THESE INSTRUCTIONS. REFER TO THEM
FREQUENTLY AND USE THEM TO INSTRUCT OTHERS
WHO MAY USE THIS UNIT. IF YOU LOAN SOMEONE
THIS UNIT, LOAN THEM THESE INSTRUCTIONS ALSO.
PRODUCT SPECIFICATIONS
Motor
No Load Speed
Blade Length
Cutting Capacity
Weight With Battery Pack
Battery pack
Charger
FEATURES
Fig.1
A. BLADE COVER
B. GUARD
C. FRONT HANDLE
D. TRIGGER LOCK BUTTON
E. REAR HANDLE
F. BATTERY PACK
I I P P NL NL S S DK DK
18V
1200 min-1
457 mm
10 mm
3,2 kg
BPP-1817M / BPP-1815M /
BPP-1817MG /ABP1801/
ABP1802 / BPL-1815 /
BPL-1820 / BPL-1820G
BC-1800 /
BC-1800M / BC-1815S /
BC-1815SMG /
ACR1800 / BCL-1800 /
BCL-1800G
N N FIN GR HU FIN GR HU CZ RU CZ RU
English
G. BLADE
H. SENSOR SWITCH
I. TRIGGER
Fig. 2
A. BATTERY PACK
B. LATCHES
Fig. 3
A. FRONT HANDLE
B. SENSOR SWITCH
C. TRIGGER LOCK BUTTON
D. TRIGGER
Fig. 6
A. BLADE COVER SCREWS
B. BLADE COVER
Fig. 7
A. BLADE SCREWS
B. BAR PLATE
C. RETAINING RING
D. WASHER
E. RETAINING PLATE
F. CUTTER BLADE ASSEMBLY
G. YOKES
H. CAMS
I. PINS
Fig.9
A. CUTTER BLADE
B. GUARD
Fig. 10
A. BLADE COVER
Fig. 11
A. BATTERY CHARGER
B. GREEN LIGHT
C. RED LIGHT
OPERATION
LED FUNCTIONS OF CHARGER
See Figure 11.
LED WILL BE ON TO INDICATE STATUS OF CHARGER
AND BATTERY PACK:
Red LED on = Fast charging mode.
Q
Green LED on = Fully charged battery pack.
Q
No LED on = Defective charger or battery pack.
Q
14
RO PL SLO HR TR EST LT RO PL SLO HR TR EST LT
CAUTION
To prevent damage to battery pack, remove
battery pack from charger immediately if no LED
comes on. Return battery pack and charger
to your nearest Authorised Service Centre for
checking or replacing. Also, if you are removing
battery pack from charger and no LEDs are on,
return both battery pack and charger to your
nearest Authorised Service Centre. Do not insert
another battery pack into charger. A damaged
charger may damage a battery pack.
LV LV SK BG SK BG