Seamaid LEDINPOOL 502877 Manuel D'utilisation page 7

UK
IMPORTANT: this instruc�on manual contains highly
important informa�on about safety measures to be taken
when installing and commissioning the device. It is therefore
important for you to read these instruc�ons before assembling and
opera�ng the product. Please keep this manual for later use. Lack
of compliance with the instruc�ons stated in this manual during
the installa�on, opera�ng and maintenance phases shall relieve
the manufacturer or distributor of any liability in the face of
damages caused to people, to the product or to the installa�on
site, and will result in you losing the warranty.
1. GENERAL INFORMATION
This LED light was designed for immersed use in swimming water. It is a class III
ligh�ng system with Safety Extra Low Voltage of ∿12V(AC) or ⎓20V(DC). The light
source cannot be replaced. If it stops working, the en�re light will need replacing.
It has an IP68 protec�on level and must be installed at a maximum immersed
depth of 1 metre. This light also complies with interna�onal light safety standards,
in par�cular standard IEC 60598-2-18 pertaining to swimming pool lights. It must
be connected to a flexible power lead with a minimum size of 2x1mm².
2. INSTALLATION
Correct installa�on requires for the light's power circuit to be protected by a
residual current device, with a maximum intensity of 30 mA. This light can only be
connected to a double-insulated transformer or a double-insulated compa�ble
stabilised safety power source. Any other type of voltage transformer is
prohibited. We recommend for the transforma�on power to be higher than the
total power of all lights connected to the device. The manufacturer or distributor
can in no way be held responsible for the assembly, installa�on or opera�on of
the product if it was manipulated or if non-provided electrical components were
added.
3. ASSEMBLY AND REPLACEMENT
Please refer to the instruc�on sheet provided in this manual.
4. MAINTENANCE
This LED light does not require any form of maintenance. When the LED on the
remote control no longer lights up, its ba�ery (model CR2032/3V/120mAh) needs
to be replaced. If the light malfunc�ons, please contact either our customer
service department, or that of your retailer.
5. USAGE
This LED light should be used like any tradi�onal incandescent lamp for swimming
pools. Commands are given through the main ON/OFF switch on the pool's
electrical panel. You also have the op�on of connec�ng a remote control module
of the same brand.
The system offers a 16-programme cycle (11 set colours and 5 automa�c colour
splashes). It requires manual control, once the power has been cut.
<3 s: switch to the following programme
On
>15s: switch back on to the programme selected prior to the
power cut
OFF >20s + ON 3-5s + OFF 3-5s + ON: light synchronisa�on
Off
(mul�ple installa�ons)
Using the remote control requires you to be at a maximum distance of 10 metres
from the light. The presence of metal, concrete or deep immersion can restrain
the use of the remote control to a much shorter distance (1 to 2 metres). When
first using the remote control, you will need to configure it with its receiver -
already integrated in the light system. (Please refer to the instruc�ons in this
manual)
On/Off (O): Switched on/Standby
Colors (C): Access to 11 set colours
Programs (P): access to 5 colour splashes
Synchro (S): light synchronisa�on
6. SAFETY WARNINGS
- Before working on the light, it must be unplugged from the
electrical network
- All electrical connec�ons must be done outside the water
- Never work on the device with wet feet
- All preven�on standards currently in force must be complied
with
- IEC 364-7-702 standards in par�cular must be complied with:
ELECTRICAL INSTALLATIONS INSIDE BUILDINGS. SPECIAL POOL
INSTALLATIONS
- Those in charge of assembly must be suitably qualified for
this type of work
- Switching the device off with the remote control will simply
put it on standby
- If the device stays off for more than 24h, we recommend
using the switch located just before the transformer.
7. WARRANTY
This LED light is guaranteed against any material and/or manufacturing defects
(electronic components) for 2 years star�ng from the date of delivery.
(Substan�a�ng documents must be preserved) This light is not guaranteed
against breakage caused by an external impact, a short circuit or excessive
screwing, nor against power surges caused by the main power network. (In this
case, the home insurance policy will kick in). This warranty is valid under the
strict condi�on that the assembly and maintenance instruc�ons are complied
with. Within the framework of this warranty, the manufacturer or distributor's
only obliga�on will be to have their a�er-sales service replace or repair the
product or component recognised as defec�ve for free (the choice is theirs to
make). Any other costs are to be covered by the purchaser. To benefit from this
warranty, products must first be sent in to the manufacturer or distributor's
a�er-sales service; their consent is mandatory if the product is to be replaced or
repaired. The warranty shall not apply in the case of a visible defect. Defects and
deteriora�ons caused by normal wear, malfunc�ons resul�ng from
non-compliant assembly and/or usage, and product modifica�ons made
without the manufacturer's prior wri�en consent are also excluded from the
warranty.
8. ENVIRONMENTAL INFORMATION
In accordance with European Direc�ve 2002/96/EC, pertaining to waste
electrical and electronic equipment (WEEE), the consumer must return any
used products to suitable collec�on points.
(mul�ple installa�ons)