Astralpool 59124 Manuel D'installation Et D'entretien page 3

ENGLISH
IMPORTANT: The instruction manual you are holding includes essential information on the safety measures to be
implemented for installation and start-up. Therefore, the installer as well as the user must read the instructions
before beginning installation and start-up.
Keep this manual for future reference.
To achieve optimum performance of the LumiPlus PAR56 RGB 1.11 Wireless Lamp, follow the instructions provided
below:
1. VERIFY THE CONTENTS OF THE PACKING:
59124
1 PAR56 RGB 1.11 Wireless Lamp
Installation and maintenance manual
Bag of fastenings
Warranty booklet
2. GENERAL CHARACTERISTICS:
This lamp has been designed to be used fully submerged in fresh water. It is a Class III electric apparatus with very
low safety voltage (12 V with alternating current). The lamp is class 116, in accordance with standard EN 50065.
The floodlamp complies with IPX8 degree of protection at a nominal immersion depth of 2 m.
This floodlamp complies with international safety standards for lights, especially the EN 60598-2-18 standard: LIGHTS
PART 2: SPECIFIC REQUIREMENTS SECTION 18 LIGHTS FOR SWIMMING POOLS AND SIMILAR APPLICATIONS.
LumiPlus Control Motion must not be washed or immersed in water.
The manufacturer is not responsible in any circumstances for assembly, installation or start-up of any electric compo-
nents which have been inserted or handled at locations other than its own premises.
3. INSTALLATION PAR56 RGB 1.11 WIRELESS LAMP:
• To correctly light a swimming pool we recommend install a lamp in the range LumiPlus 1.11 every 20 m² of water
surface. Recommendation valid for light coloured pools. In darker coloured pools we recommend oversizing the
proportion of lamps per m².
• The connection boxes should be at least 2 m. from the edge of the swimming pool or water installation.
• The 230/12V transformer supplying the lamp, should be installed 3.5 m. from the edge of the swimming pool or
water installation.
• Conduits installed less than 3.5 m. from the swimming pool edge, should not be lined or covered in metal.
4. ASSEMBLY:
To remove the projector to the edge of the swimming pool (Fig. 1) loosen the two screws of the decorative ring until the
fixation system fastening dog yields sufficiently so that the projector unit can be separated from the housing.
1. Ensure that the lamp is NOT receiving voltage.
2. Unscrew the 6 nuts that fix the trim ring at the bottom of the projector (Fig. 2).
Unscrew the two cap nuts (Z), and completely unscrew the two screws (X), see Fig. 3.
Extract the lamp from the inside of the bottom projector and disconnect the 2 terminals, loosening the two screws that
fix them to the lamp (Fig. 4).
3. Change the lamp and assemble the Projector, in the opposite order described, taking special care to:
• Connect the cable terminals to the lamp, using the 2 screws supplied with the lamp (Fig. 4).
• Fully centre the O-ring in its seat.
• Firmly tighten the nuts (Maximum torque 2 Nm).
It is essential that the direction of the lamp is adequate, situating "TOP" on the top part of the projector.
5. MAINTENANCE PAR 56 RGB 1.11 WIRELESS LAMP:
This lamp does not require any type of maintenance work. If you notice that the lamp is not working properly, please
contact our customer attention service.
THIS LAMP DOES NOT CONTAIN ANY ELEMENTS THAT CAN BE HANDLED, DISMANTLED OR REPLACED BY THE
USER. IT IS FORBIDDEN TO ACCESS INSIDE THE PRODUCT, OTHERWISE THE GUARANTEE OF THE PRODUCT
59126
1 PAR56 RGB 1.11 Wireless Lamp
+1 LumiPlus Control Motion
Installation and maintenance manual
Bag of fastenings
Warranty booklet
WILL BECOME INVALID.
3
59127
2 PAR56 RGB 1.11 Wireless Lamps
+ 1 LumiPlus Control Motion
Installation and maintenance manual
2 Bags of fastenings
Warranty booklet