Useful Tips For Recording - Sony MDS-JA30ES Mode D'emploi

Useful Tips for Recording

TIME EDIT/NO
POWER
g
TIMER
REC OFF PLAY
SCROLL/ DISPLAY/
INPUT FILTER CLOCK SET CHAR
PHONES PHONE LEVEL OPT1
OPT2 • COAX
ANALOG
PLAY MODE REPEAT TIME
0 10
§ OPEN/CLOSE
INPUT
Checking the remaining recordable time on
the MD
Press TIME.
• When you press the TIME button repeatedly while
recording, the display alternates between the
recording time of the current track and the
remaining recordable time on the MD.
• When you press the TIME button repeatedly while
the deck is stopped, the display alternates between
total disc playing time and remaining recordable
time on the MD (see page 20).
Monitoring the input signal (Input Monitor)
Before starting recording, you can monitor the selected
input signal through the deck's output connectors.
1 Press § OPEN/CLOSE to remove the MD.
2
Set INPUT according to the input signal you want
to monitor.
When the INPUT switch is set at ANALOG
The analog signal input through the
LINE(ANALOG) IN connectors is output to the
DIGITAL OUT OPTICAL connector after A/D
conversion, and then to the LINE(ANALOG) OUT
connectors and the PHONES jack after D/A
conversion.
When the INPUT switch is set to a digital source
After passing through the sampling rate converter,
the digital signal input through the respective
DIGITAL IN connector is output to the DIGITAL
OUT OPTICAL connector, and after D/A
conversion to the LINE(ANALOG) OUT
connectors and PHONES jack. Either "32kHz",
"44.1kHz", or "48kHz" appears in the display
depending on the sampling rate of the digital
signal.
3
Press r REC.
If the INPUT switch is set at ANALOG, "AD-DA"
appears in the display.
If the INPUT switch is set at a digital position,
"-DA" appears in the display.
If "Auto Cut" appears in the display
(Auto Cut)
There has been no sound input for 30 seconds during
≠ AMS ±
recording. The 30 seconds of silence are replaced by a
blank of about 3 seconds and the deck changes to
recording pause.
≠ ±
EDIT/ AMS DIGITAL REC LEVEL ANALOG
NO YES 0 5
4 6
3 7
0 ) 2 8
1 9
+
– 0 10
PUSH ENTER L R
z
§ ( P p r
OPEN/CLOSE REC
( p r REC
If "Smart Space" appears in the display
(Smart Space)
There has been an extended silence of 4 to 30 seconds
in length during recording. The silence is replaced
with a blank of about 3 seconds and the deck continues
recording. Note that new track numbers may not be
marked for portions recorded while this function is
activated.
To turn off the Smart Space Function and Auto Cut
Function
1 While the deck is stopped, press EDIT/NO twice.
2 Turn AMS to display the S08 menu, then press
3 Turn AMS to select "S.Space Off", then press AMS.
4 Press EDIT/NO.
To turn on the Smart Space Function and Auto Cut
Function again
1 Do Steps 1 and 2 in "To turn off the Smart Space
2 Turn AMS to select "S.Space On", then press AMS.
3 Press EDIT/NO.
Notes
• When you turn off the Smart Space Function, the Auto Cut
• The Smart Space Function and Auto Cut Function are
• The Smart Space Function does not affect the order of the
• If you turn off the deck or disconnect the AC power cord,
Recording on MDs
You can turn off the Auto Cut Function
For details, see "To turn off the Smart Space Function
and Auto Cut Function" below. Note that when you
turn off the Auto Cut Function, the Smart Space
Function is turned off automatically.
AMS.
Function and Auto Cut Function" above.
Function is also turned off automatically.
factory set to on.
track numbers being recorded, even if the blank space
occurs in the middle of a track.
the deck will recall the last setting (On or Off) of the Smart
Space and Auto Cut Functions the next time you turn on
the deck.
(Continued)
11 EN