Supra NÉO 100 Notice D'installation Et D'utilisation page 14

You have just purchased an appliance from our range. We would like to congratulate you on your choice. This appliance has been
carefully designed. In order to get the very best out of it, we would advise you to request the services of one of our specialists. This will
ensure that the installation is done in accordance with good practices and will guarantee the best operating and safety conditions,
bearing all the responsibility for the final installation. The appliance has to be connected to a suitable individual flue, using the
appropriate fittings. Some of the accessories provided have to be must be readily available before installation.
Before lighting the fire for the first time, please read these installation and operating manual carefully. Retain the manual and warranty,
which indicates the model and serial Nº. The person performing the installation work shall be fully liable for any failure to comply with
the instructions set out in these two documents.
Your chimney «draws well», but you are unsure of the draught value. The chimney draught is measured in Pascal (Pa). The
inserts, fireboxes and stoves have been designed, optimised and manufactured in accordance with standards NF EN 13229
(or NF EN 13240) to operate connected to a chimney with a draught of 12 Pa. It frequently happens (in more than one in two
chimneys) that the draught is far too high (over 20 Pa) due to the fact that the chimney is either too high or due to the flue
liner. In this case, the appliances will operate in abnormal conditions which may lead to:
- Excessive wood consumption: this can be three times as much as an appliance with a draught of 12 Pa.
- A fire that "keeps going out" and burns too quickly while producing insufficient heat.
- A quick and inevitable deterioration of the appliance (cracks in the cast iron panels or in the refractory bricks)
- A voided warranty.
To avoid all these problems, there is only one solution!
Get a professional to check the chimney draught (with the appliance operating) and, if it is above 20 Pa, then install a damper
or an adaptor at the flue connection.
1. TECHNICAL DATA
FIREPLACE INSERT
Stove category
Rated heat output (1)
Operating mode
Average flue gas temperature with the door closed
Efficiency
Seasonal efficiency
CO concentration (13% 02)
CO2 concentration (13% 02)
Dust concentration (13% 02)
VOC
NOX
Fuel
Log size
Nominal load per hour approx.
Refuelling
Prohibited fuels
Approx. flue gas mass flow
Flue pipe nominal diameter
Characteristics of the flue pipe
Chimney flue minimum dimensions
Ø min. flue lining or insulated metal duct
Minimum height above the hearth
Diameter of combustion air collar
Ventilation of the room
Draught (10 Pa = 1 mm CE)
Nominal efficiency
Performance in slumber mode (min. permitted)
Max. permitted
Net/gross weight
Air connection collar
Accessories supplied
Cold hand key, heat-insulated glove, finishing frame, combustion air connection collars ø 75.
Option available
1000 Fan kit
Casing kit (for insert assembly or hot air distribution of the hearth assembly)
Hot air distribution collars (Ø125 or Ø150) (only for hearth installation)
Beam protection kit
Feet
(1) Nominal operating power with door closed, wood fuel; according to tests carried out as per EN 13229 standard.
(2) DTU 24.1 covering flue ducting, DTU 24.2 covering chimneys equipped with a closed stove; NF EN13229 covering solid fuel stoves.
(Available at AFNOR).
- IMPORTANT -
- IMPORTANT ASSEMBLY INFORMATION -
NEO 100
Intermittent
10 kW
Only with the door closed
269 °C
80.6 %
70.6%
0.09 %
9.88 %
40 mg/Nm
127.2 mg/Nm
83.4 mg/Nm
Wood
50 cm
2.8 kg/h
45 min
All the rest, including coal and its derivatives
8.4 g/s
Male 180 mm
20 x 20 cm
180 mm
4 m
Male 75 mm
1.2 dm²
12 Pa ± 2 Pa
6 Pa ± 1 Pa
20 Pa
152 kg/182 kg
Nameplate on the ash box
Ø 75 inside the appliance
Option; requires the 1000 casing option
PS 1000 option
Option; requires the 1000 casing option
Option
Option PS 100
3
3
3